Safety Guidelines; Need More Information - Dell D00D Schnellstartanleitung

Setting Up Your Cloud Client
Be sure you have read Safety Guidelines before setting up and operating
this product. Refer to the figures and proceed as follows:
1. Make sure that the monitor and the cloud client are turned off and
disconnected from AC power. Place the cloud client on a desk, or
use a Dell-approved mounting accessory kit.
2. Make all desired connections (video display and keyboard with
mouse are required). Connection to a 10/100/1000 Base-T Ethernet
network is required unless an optional WiFi network adapter is used
for wireless connection to a network. For connection to Fiber SFP,
make sure the SFP module (ordered/shipped separately) is
unlocked. Plug it into the SFP/Mini-GBIC slot, and then rotate the
latch to lock the module in place. Additional connections of
peripheral devices may be made to the other ports.
3. Connect the power adapter to the cloud client power input before
connecting to a 100-240V AC, 50-60 Hz electrical outlet, and then
press the power button to apply power. When the initialization
sequence is complete, the amber activity light changes to green.
Default User Names and Passwords
(Case Sensitive)
™
Wyse ThinOS
Administrator
User Name —
Password —
User
User Name —
Password —
* For administrators, log off User desktop while holding down the Shift key until the logon box
appears.
Cloud desktop - WSM software is required; no operating system is installed, and
therefore no default user name and password are defined. Information about setting up
your server environment is available in the WSM documentation.

Safety Guidelines

Improper connection, mounting, or use of this product could result in
component failure or undesired interference. Read the following
guidelines before setting up and operating the device.
Setup
•
Do not connect to AC power until all other connections (including
the power adapter) are made. Connecting or disconnecting
components or equipment on the back panel when the device is
receiving AC power can cause power surges and damage the device.
•
Do not force a connector into its socket. If any undue resistance is
encountered, ensure that the connector is correctly oriented to the
receptacle.
•
For wireless usage and requirements, refer to the regulatory notices in
the device's documentation.
Venting and Care
•
Mount the device only as shown or in accordance with the
instructions provided with Dell-approved mounting accessory kits.
Improper orientation could restrict airflow of heat from the device
and damage it.
•
Allow sufficient space around the device for ventilation; do not place
the device in any enclosure that restricts airflow around the device;
do not place any objects on the device or block the vent outlets.
For environmental operating specifications, visit:
http://www.dell.com/ccc/d00d
®
Microsoft
®
Dell Wyse Enhanced Embedded Standard
SUSE Linux Enterprise 2009 / 7 / 7B / 7p / 8 / 8B
admin administrator
admin Wyse#123
thinuser user
thinuser Wyse#123
Power Sources
•
For regulatory compliance use only the power adapter that comes
with your device or a Dell-approved equivalent. For proper
replacement compare the labels on both device and power adapter to
ensure that their voltages match.
Warning: Use of any other power adapter may damage your
device or the power adapter. The damage caused by an improper
power adapter is not covered by warranty.
•
Accidental loss of power can damage device. Avoid connecting it to
any power outlet which can be accidentally switched off. Do not hard
reset the device by holding down the power button during normal
operation.
•
When turning off the device, be sure to perform a complete
shutdown (via the user interface or a light press on the power button).
Do not disconnect the AC power cord, DC power cord, or shut off
power at a circuit breaker (including power strips), etc., to turn off the
device.
•
Surge protectors for electrical devices are recommended in areas of
lightning. However, when lightning is occurring, your equipment
should be properly shut down and unplugged from AC power until
the storm has passed.
•
Be very careful to not interrupt power while the device is
downloading a software update.
Battery
®
Windows
The device contains an internal button cell battery replaceable by Dell
*
or one of our Authorized Service Centers. For service, visit
http://www.wyse.com/support/authorized-service-centers.
Warning: There is a risk of explosion if the battery is replaced by an
incorrect type. Always dispose of used batteries according to the
instructions accompanying the battery.
Warning: Perchlorate Materials - Special Handling May Be Required
under California Code of Regulations, title 22. (Only required within the
USA.)

Need more information?

Dell Reference Guides - User, Administrator, and related
documentation is available at:
http://www.wyse.com/manuals
Dell-Approved Mounting Accessory Kits - Information about
approved mounting accessory kit options is available at:
http://www.wyse.com/products/accessories/mounting-options
Dell Service and Support - Latest software images are available at:
http://www.wyse.com/downloads
Dell Wyse Device Manager - Information about Dell remote
management software is available at:
http://www.dell.com/ccc/WDM
Dell Wyse WSM - Information about Wyse WSM software is available at:
http://www.dell.com/ccc/WSM
Dell and the Environment - Information about Dell compliance with
RoHS and with the Waste Electrical and Electronic Equipment (WEEE) is
available at:
http://www.dell.com/environment
Dell and E-Recycling - Information about recycling and reuse of Dell
products is available at:
http://www.dell.com/recycling
Dell Warranty Registration* - Register your product at:
http://www.wyse.com/registration
* The standard warranty is three years from the date of purchase.
3