Programmed Play; Alarm Function - AEG KRC 4376 CD Bedienungsanleitung

REPEAT
With a CD currently playing:
Press once = ( 1 illuminate) the current track is
repeated continuously.
Press twice = ( ALL illuminate) the whole CD is
played continuously.
Press three times = All functions are cancelled. The normal
play mode is resumed.

Programmed Play

This can be used to program any desired sequence of tracks.
1. Press the / M – button.
2. Press the CLK SET / MEM / PROG button. The storage
space "P01" appears briefl y in the display. Then the se-
lection of the track and the "PROG" display start fl ashing.
Use the SKIP / TUNE
and then press the CLK SET / MEM / PROG button again.
The display changes to memory location P02.
3. Select the next track with the
and press the CLK SET / MEM / PROG button again. Re-
peat the procedure until all the desired tracks are selected.
NOTE:
Once the storage capacity of the tracks to be pro-
grammed has been reached "
display.
/ M + button. The playback starts. The current
4. Press the
title number, the notifi cation „ " and „PROG" will be
shown in the display. Then the present playback time of
the current track appears.
5. Press the / M – button once to stop the playback while
retaining the program.
6. To play the programme back again, press the
button.
The device stops automatically after all programmed titles
have been played. The listed sequence remains in the memo-
ry until you switch to a different operating mode.
Deleting a programmed sequence
To delete the program, press the / M – button twice. The
notifi cation "PROG" will disappear.

Alarm Function

General Information
• The alarm can only be set, activated and deactivated in
standby mode.
• You want to wake up with the radio? Set the desired
station in advance.
• You want to wake up with a CD? Insert a CD into the CD
tray. If you don't insert a CD, you will automatically be
woken by the signal tone.
• If the set alarm time is reached, the word ALARM fl ashes in
the display. The volume rises slowly to the maximum value.
KRC4376CD_IM
to select the desired track
SKIP / TUNE buttons
PROG" fl ashes in the
/ M +
Setting of the Alarm
1. Switch the device into standby mode with the POWER
button
2. Keep the ALARM button pressed for ca. 3 seconds. The
hours of the currently set alarm time start to fl ash.
3. Use the buttons and
4. Press the ALARM button for confi rmation. The minutes
start to fl ash.
5. Use the buttons and
6. Press the ALARM button to confi rm. Then select how you
want to be awakened. Select from:
• BUZZ (Buzzer):
A buzzer sounds when the alarm time is reached. The
buzzer interval increases from slow to fast.
• CD:
As soon as your specifi ed alarm time has been
reached, the device will start in CD mode. The insert-
ed CD will be played starting with the fi rst title.
• FM:
As soon as your set alarm time is shown, the radio
switches on. The last set station is played.
7. Finally, press the ALARM button again.
Activate / deactivate alarm
Press the ALARM button repeatedly.
In activated alarm mode the word ALARM appears in the
display.
Switch off the alarm sound
In order to switch off the alarm until the following day please
press the POWER button.
Short-term Timer Function
You can use this function, for example, to keep an overview
of a specifi c cooking time. You can select the time both at 10
minute intervals (180 to 10 minutes), and at 1 minute intervals.
The shortest time interval available is 1 minute.
• Press the TIMER button repeatedly to set the time at 10
minute intervals. "TIMER" and the set time starts fl ashing
in the display, starting with "TIMER 180".
• To set the time at 1 minute intervals, repeatedly press the
or button.
• The timer function is activated automatically after about
10 seconds. The set time and "TIMER" are lit in the
display.
• As soon as the set time has elapsed, a signal tone will
sound. Press the TIMER button to stop the signal tone.
NOTE:
In order to stop the function ahead of time, press the
TIMER button until " " is shown in the display.
English
43
for setting.
for setting.
06.05.16