Programmation Des Trims; Trim Programming; Other Functions; Transmitter - Nine Eagles J6 Bedienungsanleitung

Trim memory
Description Steps to follow
With this function, the trim of 1. Turn on the transmitter
the elevator channel, rudder 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
channel en aileron channel can 3. turn the D-knob until the trim indicators of aileron, rudder and elevator start flashing.
be set. The transmitter will save 4. Press the A-button or the C-button. Only one indicator keeps on flashing.
the trim positions. 5. Use the D-knob in order to select the desired trim channel.
6. press the A-button or the C-button in order to confirm.
7. Use the D-knob to set the trim
8. Press the C-button to save
9. press the B-button to go back in the menu.
Throttle hold
Description Steps to follow
The throttle hold function can 1. Turn on the transmitter
be set, according to your own 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
needs. The value is a percent- 3. turn the D-knob until "G H" flashes.
age of the throttle value and 4. Press the A-button or C-button . The 3 digits on the throttle indicator will flash.
varies between 0% and 100% 5. With knob D, you can change the value of the throttle hold function. (By pressing the A-button, the
6. Press the C-button to save
7. press the B-button to go back in the menu.
Range test
Description Steps to follow
This function allows you to di- 1. Turn on the transmitter
minish the output power of the 2. Simultaneously press the A-button and B-button for one second. On the LCD screen the "MODE"
transmitter temporarily in order -icon and the "Modeltype" Icon" (helicopter or airplane) will start flashing.
to perform a range check. 3.Turn knob D until "P-H" or "P-L" flashes
4. Press the A-button or C-button and "P" on the screen will be steady
5. Use Knob D to switch from H (high power) to L (low power)
6. Press the C-button to save
7. press the B-button to go back in the menu.
Wireless copy
Description Steps to follow
The transmitters , allows to 1. Turn on the transmitter
exchange its data with other 2. Simultaneously press the A-button and B-button for one second. On the LCD screen the "MODE"
transmitters of the same brand -icon and the "Modeltype" Icon" (helicopter or airplane) will start flashing.
and type, 3. Turn the D-Knob until "C P" flashes.
4. Press the A-button or C-button to confirm
5. Use the D-Knob to choose between A or S
6. Press the C-button in order to start sending or retrieving data.
7. While copying, "-----------" is displayed on the LCD
8. press the B-button to go back in the menu.
9. Proceed the same way, if you want to copy data to another transmitter.
Transmitter power
If the transmitter is set to a state of low emitted power, a range test can be
done. A test with limited power and short distance simulates a full range test
with full power. The 2.4Ghz transmitter signal is subject to influence by it
environment. For example in a wide open area, the control distance is perhaps
30 meters, while inside a house it is perhaps only 6 meters. Always perform a
range test.
How to perform a range test:
1. Put the model on the ground and step about 30 meters away from the
model.
2. put the transmitter in the low power state
3. all functions on the model must be fully controllable with the trainer switch
activated.
D switch protection.
If the transmitter is activated and the 3D switch is still activated, an alarm
will sound and on the LCD "3d" will be displayed. Put the 3d switch back in its
normal position.
Throttle hold switch protection.
If the transmitter is activated and the throttle hold switch is still activated, an
alarm will sound and on the LCD "TH" will be displayed. Put the Throttle Hold
switch back in its normal position.
J6 transmitter
factory settings will be restored)
Binding with the receiver
Transmitter and receiver come factory synchronised when bought together
in asset. Every time you use a new transmitter or receiver, it is necessary to
synchronize the receiver with the transmitter .
Remark: make sure there is no other transmitter activated while binding.
Instructions:
Turn off both transmitter and receiver. Push the trainer switch towards the front
and hold it there while activating the transmitter. On the LCD 'SH' flashes and
an acoustic signal is released. Turn on the receiver and keep the transmitter
near the receiver. After a few seconds, the servos connected to the transmitter
will make start making small movements, indicating that the binding procedure
has succeeded.
Switching between mode 1 and Mode 2
You can change the mode of the J6 transmitter by operation just one switch.
Turn off the transmitter and remove the small cover on the back of the trans-
mitter. Move the mode switch to the other position and put the cover back
in place. All functions that occur in mode 1 and Mode 2 will have changed,
including the spring mechanism. The new chosen mode will appear on the LCD
‚mode1 or mode2)
Remark:
1.Always move the switch to the utmost positions, never leave it in between.
2. Make sure the transmitter is turned off when changing the mode
copyright © 2012 BMI
Instructions
The values of the sub trim functions may vary
from -100% to +100%
Instructions
Instructions
"You can diminish the transmitters output power
temporarily
(L) = Low
(H)= High
The normal setting is ""H"" Pay attention, never
to fly your helicopter or airplanes when the
power has been diminished. A tone will sound
when the transmitted power is set to LOW, in
order to warn you. Every time you restart the
transmitter, it will automatically restore to the
High power output
Instructions
(A) = Receive a copy
(5) = Send a copy
Make sure that both transmitters are next to
each other.
Always check if the new copy is complete. Never
fly if you are not sure.