Throttle Curve Programming; Example Curve; Gyro Sensitivity; Mode1 / Mode 2 Switch - Nine Eagles J6 Bedienungsanleitung

5 point throttle curve & Pitch Curve
Description Steps to follow
Setup of the 5 points throttle 1. Turn on the transmitter
curve 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
3. turn the D-knob until only the "123456" symbol flashes.
4. Press the A-button or C-button. The active channel is displayed
5. Turn the D-knob until ""dot"" appears on the screen (this is the case for the
throttle and the pitch channel)"
6. Press the A-button or the C-button. The number of the corresponding dot (dot n°1 to dot n°5) will flash
7. Turn knob D in order to select the desired dot.
8. Press the A-button or C-button in order to set a value for this point.
9. Use knob D to set the value.
(press the A-button to restore factory settings)
10. Press the C-button to save the change
11. Press the B-button to go back in the menu.
Examples
Description Steps to follow
Example: 1. Turn on the transmitter
Setting the elevator curve index 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
to +25%" 3. turn the D-knob until only the "123456" symbol flashes.
4. Press the A-button or C-button. channel 1 will now flash
5. Turn the D-knob until channel 2 appears on the screen
6. Press the A or C-button. The first two digits on the throttle indicator will flash, follow by "E"
7. Turn knob D until "+25" is displayed as value.
8. Press the C-button to save the change
9. Press the B-button to go back in the menu.
Description Steps to follow
"Example: 1. Turn on the transmitter
2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
Setting a 5 point PITCH curve 3. turn the D-knob until only the "123456" symbol flashes.
with these 3D values: 4. Press the A-button or C-button. channel 1 will now flash
dot 1: 30% 5. Turn the D-knob until channel 6 appears on the screen Down on the screen ""dot"" is displayed. µ"
dot 2: 35% 6. Press the A-button or the C-button. "1" (dot n°1) will flash
dot 3: 40% 7. Press the A-button or C-button. "1" (dot 1) keeps flashing. 3 digits on the throttle indicator will flash as well.
dot 4: 45% 8. Turn the D-knob until the value for dot 1 is 030
dot 5: 52% 9. Confirm by pressing the C-button. "2" (dot 2) will start flashing.
remark : the setup of the throt- 10. Press the A-button or C-button. "2" (dot 2) keeps flashing. On the throttle indicator, 3 digits flash as well.
tle curve is described on the 11. Turn the D-knob until the value for dot 2 is 035
pages 11~12" 12. Press the C-button to confirm. "3" (dot 3) will start flashing.
13. Press the A-button or C-button. "3" (dot 3) keeps flashing. On the throttle indicator, 3 digits flash as well.
14. Turn the D-knob until the value for dot 3 is 040
15. Press the C-button to confirm. "4" (dot 4) will start flashing.
16. Press the A-button or C-button. "4" (dot 4) keeps flashing. On the throttle indicator, 3 digits flash as well.
17. Turn the D-knob until the value for dot 4 is 045
18. Press the C-button to confirm. "5" (dot 5) will start flashing.
19. Press the A-button or C-button. "5" (dot 5) keeps flashing. 3 digits on the throttle indicator will flash as
well.
20. Set the value of dot 5 to 052 with knob D
21. Press the C-button to confirm
22. Press the B-button twice in order to go back in the menu.

Gyro sensitivity

Description Steps to follow
This function allows you to set 1. Turn on the transmitter
the sensitivity of the gyroscope. 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
3. turn the D-knob until only the "G-S" symbol flashes.
4. Press the A-button or C-button and 3 digits on the throttle indicator will flash.
5. Use knob D to change the value of the gyro sensitivity. (By pressing the A-button, the factory setting
will be restored)
6.. Press the C-button to save the new value
7. Press the B-button twice in order to go back in the menu.

copyright © 2012 BMI
Instructions
The throttle curve is a five dot curve that can be
set from the minimum throttle stick position
(dot 1) to the maximum throttle stick position
(dot 5). dots 2,3,4 are in between. Dot 3 cor-
responds the middle position of the throttle stick.
values vary between 0% and 100%
Instructions
When a channel has been chosen, the throttle
indicator displays the current curve index, fol-
lowed by an ""E""
A positive value(+) means that the sensitivity
around the middle point of the control stick is
bigger and smaller at the ends. A negative (-)
curve index has an opposite effect.
Instructions
When moving the cursor to the channel 3 or 6, it
will automatically display ""dot"" on the LCD.
This means that the Throttle and Pitch curves
are 5 dot operation curves, and thus can be set
on 5 different dots.
Please remark that after setup, no ""E"" will
appear on the throttle indicator.
Instructions
Use the switch SW(C) during setup in order
to program 2 different values. You can flip the
switch during flight if more or less gyro sensitiv-
ity is required.
J6 transmitter