Dual Rate Function; Wing Mixers; Curve Programming - Nine Eagles J6 Bedienungsanleitung

Servo reverse function
Description Steps to follow
1. Turn on the transmitter
2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
3.Press the A-button or the C-button to confirm.
Make sure the channel is setup 4. Select the channel you wish to reverse, using the D-knob
in the right position, according 5. Confirm your selection, by pressing the C-button.
to the installation position of 6. Turn knob D in order to choose "NOR" or "REV"
the servo 7. Press the C-button to save the changes and enter into the next channel.
8. Press the B-button to return in the menu.

Dual Rate Function

Description Steps to follow
When choosing high rate or 1. Turn on the transmitter
low rate mode for the ""AIL"", 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
""ELE"" or ""THR"" channels, 3. turn the D-knob until the "D/R indicator" and n "123456" flash on the screen.
you can set two values for the 4. Press the A-button or the C-button to confirm.
control stick's both directions 5. Select the channel you wish to modify, using the D-knob.
(left/right and up/down) 6. Press the A-button or the C-button in order to confirm your choice.
separately. 7. Turn the D-knob to set the rudder value. use the D/R switch to choose high rate mode or low rate
mode. Move the corresponding channel stick to select the rudder value for the left/right or up/down
sides. (Press the A-button to restore factory settings)
7. Press the C-button to save the changes and enter into the next search.
8. Press the B-button to return in the menu.

Wing mixers

Description Steps to follow
This function provides 3 kinds 1. Turn on the transmitter
of basic wing mixer parameters 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
and asymmetric value setup of 3. turn the D-knob until the "MIX " symbol and the "123456" symbol flash on the screen.
the sticks. 4. Press the A-button or C-button, and the "123456" symbol disappears (unless these parameters have
been set before)
5.Select the preferred wing type, by turning the D-knob
6. Press the A-button or C-button and "MIX" and the wing configuration will flash
7. Turn the D-knob in order to select main channel or
sub channel."
8. Press the A-button or the C-button in order to confirm your choice.
9. Turn the D-Knob to set the 'wing mix' value, use the corresponding control stick to change the
parameters.
(press the A-button to restore the factory settings) "
10. Press the C-button to save the changes and enter into the next search.
11. Press the B-button after finishing setup.
Wing mixers
Curves
Description Steps to follow
"This function allows you to 1. Turn on the transmitter
change the curve setup which 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
can improve the operational 3. turn the D-knob until only the "123456" symbol flashes.
feeling of the control sticks. 4. Press the A-button or C-button. The active channel is displayed
You can set a negative or posi- 5. Use knob D to select a channel
tive curve index for aileron, rud- 6. press the A-button or C-button. The active channel and two digits on the throttle indicator will start
der and elevator. The throttle flashing, followed by a "E"
channel has a 5 points curve. 7. Turn the D-knob to set the curve. Press the A-button in order to restore the factory settings)
8. Press the C-button to save the changes and enter into the next option.
You'll find an explanation about 9. Press the B-button to return in the menu.
curve indices further below.
4
copyright © 2012 BMI
Wing mixers, example 1, 2 ou 3
Instructions
The LCD screen displays the current 'NOR/REV'
settings of every channel. It is necessary to
confirm every modification with the C-but-
ton. Please pay attention that every time you
change REV/NOR settings, these changes have
immediate effect on the model. Especially when
reversing the throttle channel. We recommend
you to remove rotor blades when reversing the
throttle channel.
Instructions
"When a specific channel has been selected,
the current D/R value will be displayed on the
screen. In the D/R menu, each channel has 4
parameters that can be set, by using the D/R
switch and the corresponding stick.
Values can be restores to factory settings by
pressing the A-button.
D/R values vary between -125% and +125%
Remark: a negative value indicates that the
control directions is opposite to the swing direc-
tion of the stick."
Instructions
- If no figure is shown, no wing mixer is set
- ""1"" represents a delta wing type mixer
- ""2"" represents a v-tail mixer
- ""3"" represents a flap/aileron mixer.
Use the control sick of each channel, to change
the parameter of left/right or up/down in the
wing mixer setup.
Press the A-button to restore the factory set-
tings. Press C to cancel the setting value of the
wing mixer.
Aileron channel
1
Aileron channel
Aileron channel
Avion 2
Aileron channel
Aileron channel
3
Aileron channel
Instructions
"When you have selected the channel, the
displays shows the current curve index, followed
by ""E""
A positive curve index means that the stick
movement has a much throw around the middle
point and few throw at both ends.
The effect is opposite when the curve index is
negative.
for Delta wing
for V-tail
for flaps/ailerons
J6 transmitter