Trims Programming; Helicopter Programming; Model Type Setup; Swash Plate - Nine Eagles J6 Bedienungsanleitung

Trim memory setup
Description Steps to follow
With this function, the trim of 1. Turn on the transmitter
the elevator channel, rudder 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
channel en aileron channel can 3. turn the D-knob until the trim indicators of aileron, rudder and elevator start flashing.
be set. The transmitter will save 4. Press the A-button or the C-button. Only one indicator keeps on flashing.
the trim positions. 5. Use the D-knob in order to select the desired trim channel.
6. press the A-button or the C-button in order to confirm.
7. Use the D-knob to set the trim
8. Press the C-button to save
9. press the B-button to go back in the menu.
B:Control of model helicopters
There are several possibilities to use this transmitter in combina-
tion with model helicopters , ...
Modeltype, channel reverse, dual rate, swash plate mixers,
curves, trims,..... can all be setup. Below you'll find an overview
of all switches.

Model Type setup

Description Steps to follow
"This function offers two pos- 1. Turn on the transmitter
sibilities: 2. Simultaneously press the A-button and B-button for one second. On the LCD screen the "MODE"
Airplanes or Helicopters -icon and the "Modeltype" Icon" (helicopter or airplane) will start flashing.
"3.Turn the D-Knob until the ""Mode""-icon and the
Attention ! ""model type""-icon (helicopter or airplane) flash together on the LCD screen"
A lot of the parameters 4. Next press the C-button or the A-button. The Modeltype icon keeps flashing.
described below are specifically 5. Select the desired model type (helicopter or aeroplane), by turning the D-Knob.
for helicopters and will only 6. Press the C-button to confirm your choice and its corresponding parameters
function if the model type setup 7. Press the B-button to go back in the menu.
has been set to Helicopter. "
Swash plate type
Description Steps to follow
"This transmitter offers two 1. Turn on the transmitter
swash plate types : CCPM90° 2. Simultaneously press the A-button and B-button for one second. On the LCD screen the "MODE"
and CCPM120° -icon and the "Modeltype" Icon" (helicopter or airplane) will start flashing.
Select the swash plate type that "3.Turn the D-Knob until the ""Mode""-icon and the
matches your helicopter" swash plate icon (circle) flash together on the LCD screen"
4. Next press the C-button or the A-button. The "MODE" icon is steady, while the Swash plate icon
keeps flashing.
5. Select the desired swash plate type with the D-Knob.
6. Press the C-button to save the change
7. Press the B-button to leave the menu.
Servo reverse function
Description Steps to follow
Make sure the channel is setup 1. Turn on the transmitter
in the right position, according 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
to the installation position of 3.Press the A-button or the C-button to confirm.
the servo 4. Select the channel you wish to reverse, using the D-knob
5. Confirm your selection, by pressing the C-button.
6. Turn knob D in order to choose "NOR" or "REV"
7. Press the C-button to save the changes and enter into the next channel.
8. Press the B-button to return in the menu.
6
copyright © 2012 BMI
Instructions
The values of this sub trim functions may vary
from -100% to +100%
Instructions
"The model type option includes two options:
Airplane or helicopter.
An alteration of the model type will modify all
parameters of the current model to the default
factory settings. So be careful when using this
function. If you are not sure, do NOT press the
C-button, in order to avoid replacing the settings
by default values. After changing the model
type, it is recommended to restart the transmit-
ter, in order to make sure that your changes
have been saved.
Instructions
"There are two kinds of swash plates available in
the program:
CCPM 120°
CCPM 90°"
Instructions
The LCD screen displays the current 'NOR/REV'
settings of every channel. It is necessary to
confirm every modification with the C-but-
ton. Please pay attention that every time you
change REV/NOR settings, these changes have
immediate effect on the model. Especially when
reversing the throttle channel. We recommend
you to remove rotor blades when reversing the
throttle channel.
J6 transmitter