Ccpm Mixing; Dual Rate Programming; Wing Mixers; Curve Programming - Nine Eagles J6 Bedienungsanleitung

CCPM Mix setup
Description Steps to follow
This function is used to setup a 1. Turn on the transmitter
120°CCPM swash plate system. 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
You can set the throw and "3.Turn the D-Knob until the ""123456""-icon and the
direction of every individual ""swash plate ""-icon (circle) flash together on the LCD screen"
swash plate servo. 4. Press the C-button or A-button and the swash plate icon and channel identifier keep flashing.
5. Select the desired channel with the D-knob
6. Confirm the chosen channel by pressing the A-button or the C-button.
"7. Change the value, using knob D
(Press the A-button in order to restore the factory setting)"
8. Press the C-button in order to save the changes and to go to the next channel.
9. Press the B-button to leave the menu.
Dual Rate Function
Description Steps to follow
When choosing high rate or 1. Turn on the transmitter
low rate mode for the ""AIL"", 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
""ELE"" or ""THR"" channels, 3. turn the D-knob until the "D/R indicator" and the "123456" indicator flash on the screen.
you can set two values for the 4. Press the A-button or the C-button to confirm.
control stick's both directions 5. Select the channel you wish to modify, using the D-knob.
(left/right and up/down) 6. Press the A-button or the C-button in order to confirm your choice.
separately. 7. Turn the D-knob to set the rudder value. use the D/R switch to choose high rate mode or low rate
7. Press the C-button to save the changes and enter into the next search.
8. Press the B-button to return in the menu.

Wing mixers

Description Steps to follow
This function provides 3 kinds 1. Turn on the transmitter
of basic wing mixer parameters 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
and asymmetric value setup 3. turn the D-knob until the "MIX " symbol and the "123456" symbol flash on the screen.
of the sticks for helicopters or 4. Press the A-button or C-button, and the "123456" symbol disappears (unless these parameters have
airplanes.
5. Select the preferred wing type, by turning the D-knob
6. Press the A-button or C-button and "MIX" and the wing configuration will flash
7. Turn the D-knob in order to select main channel or
8. Press the A-button or the C-button in order to confirm your choice.
9. Turn the D-Knob to set the 'wing mix' value, use the corresponding control stick to change the
10. Press the C-button to save the changes and enter into the next search.
11. Press the B-button after finishing setup.
Curves
Description Steps to follow
"This function allows you to 1. Turn on the transmitter
change the curve setup which 2. Press the A-button for 1 second and the "NOR REV" symbol and "123456" symbol will start flashing.
can improve the operational 3. turn the D-knob until only the "123456" symbol flashes.
feeling of the control sticks. 4. Press the A-button or C-button. The active channel is displayed
You can set a negative or posi- 5. Use knob D to select a channel
tive curve index for aileron, rud- 6. press the A-button or C-button. The active channel and two digits on the throttle indicator will start
der and elevator. The throttle
channel has a 5 points curve. 7. Turn the D-knob to set the curve. Press the A-button in order to restore the factory settings)
8. Press the C-button to save the changes and enter into the next option.
You'll find an explanation about 9. Press the B-button to return in the menu.
curve indices further below. "
Curves can be set between - 80% en +80%"
J6 transmitter
mode. Move the corresponding channel stick to select the rudder value for the left/right or up/down
sides. (Press the A-button to restore factory settings)
been set before)
sub channel.
parameters.
(press the A-button to restore the factory settings) "
flashing, followed by a "E"
Stick movement
Curve index 0%
Stick movement
Curve index 60%
copyright © 2012 BMI
Instructions
In step 5
Channel 1 : represents the Aileron channel.
Channel 2: represents the elevator channel.
Channel 3 : represents the Pitch channel.
The parameters of every channel vary between
-100% and +100%
Instructions
When a specific channel has been selected,
the current D/R value will be displayed on the
screen. In the D/R menu, each channel has 4
parameters that can be set, by using the D/R
switch and the corresponding stick.
Values can be restores to factory settings by
pressing the A-button.
D/R values vary between -125% and +125%
remark: a negative value indicates that the
control directions is opposite to the swing direc-
tion of the stick.
Instructions
Specific mixers for helicopters:
- If no figure is shown, no wing mixer is set
- ""1"" represents an ATS type mixer, where the
corresponding values for the throttle channel
and the tail channel (rudder) require setup. Use
the corresponding control stick of each channel
in order to change the parameter of left/right or
up/down. in the wing-mixer.
Press the A-button to restore the factory set-
tings. Press C to cancel the setting value of the
wing mixer.
Instructions
When you have selected the channel, the display
shows the current curve index, followed by ""E""
A positive curve index means that the stick
movement has a much throw around the middle
point and few throw at both ends.
The effect is opposite when the curve index is
negative.
Normal curves can be set between -80% and
+80%
Stick movement
Curve index-60%