Overview Of The Components - AEG DAB 4138 Bedienungsanleitung

Overview of the components

Front
1 Telescopic antenna
2 LCD display
3 / buttons (Scan forwards/ backwards)
4 VOL+/VOL buttons (volume)
5 SCAN button (scan)
6 MENU button (open menu)
7 INFO button (show information)
8 POWER button (standby/ operation)
9 REPEAT ALARM/SELECT button (repeat alarm/ confirm)
10 ALARM ON/OFF button (alarm On/ Off)
11 SOURCE button
12 PRESET button
13 SLEEP button (snooze)
Rear view (without illustration)
Battery compartment
DC IN 6 V connector
OFF/ON switch (On / Off)
Installation
• Read the manual thoroughly before operating the de-
vice!
• Choose a suitable location for the device. Suitable loca-
tions are dry, even and antislip surfaces on which you may
operate the device easily.
• Make sure there is proper ventilation for the device!
• Remove, if necessary, the protection sheet from the
display.
Power supply (Adaptor)
• Insert the grid plug into a properly installed three prong
socket. Connect the device with the plug connector by
inserting its plug into the DC 6 V jack of the device.
• Make sure the grid voltage corresponds to the figures on
the rating plate.
CAUTION:
• Only use the supplied power adaptor for this device.
Do not use for other devices.
• Only use power adaptor with 6 V (
adaptors may cause damage to the device.
NOTE:
Disconnect from mains power supply during longer periods
of non-use.
Battery Operation
You also have the option of operating the unit with 4 Type R6
"AA" batteries.
1. Open the battery compartment on the back.
2. Insert 4 R6 "AA" batteries 1.5 V. Mind the correct polarity
(indicated on the bottom of the battery case)!
3. Close the battery case.
4. If the device is not used for an extended period of time,
remove the batteries from the device to avoid any leaking
of battery acid.
CAUTION:
• Never use different battery types or new and used bat-
teries together.
• Batteries must not be disposed of in the garbage.
Please bring used batteries to competent collection
centers or back to the dealer.
WARNING:
Do not expose batteries to any high temperatures such as
sunlight, fire, or the like. There is a danger of explosion!
NOTE:
• If you have connected the power supply, the batteries
are automatically deactivated.
• Always switch off the device during non-use with the
OFF ON switch on the back, to not unnecessarily
stress the batteries. To display the time as accurately as
possible, the device will synchronize the time with the
radio station in the background. This results in a higher
battery consumption. In the worst case scenario, the
batteries could be discharged prematurely.
When shutting off the device with the OFF ON switch,
the time/ alarm time will be lost.
Installation
1. Fully extend the telescopic antenna (1). Stand it upright
for initial installation.
2. Switch the device on at the back of the device using the
OFF/ON switch. The device automatically searches for
DAB stations. SCANNING... and a progress bar appears
on the display. The figure on the right of the display
shows the number of radio stations found. The first alpha-
numeric DAB station is played.
When playing a radio station, the time and date is taken
from the broadcasting service. If the device does not re-
ceive DAB stations in your location, set the time manually
), other
as described in "Settings menu".
Changing the OSD language
The OSD menu is set in German ex factory. To change the
language, proceed as follows:
1. Press the MENU button (6).
2. Select the menu option "SYSTEM" with the / buttons
(3). Set it with the REPEAT ALARM/SELECT button (9).
3. Select the menu option "LANGUAGE" with the / but-
tons. Set it with the REPEAT ALARM/SELECT button.
4. Select the desired language with the / buttons. Set it
with the REPEAT ALARM/SELECT button.
English
39