Specifications - Makita 8413D Betriebsanleitung

ENGLISH
1 Push button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 A side
6 B side
7 Clockwise
8 Counterclockwise
9 Low speed
10 High speed

SPECIFICATIONS

Model
Capacities
Concrete ......................................................13 mm
Steel ............................................................13 mm
Wood ...........................................................30 mm
Wood screw .................................................6 mm x 75 mm
Machine screw ............................................6 mm
-1
No load speed (min )
High .............................................................0 – 1,300
Low ..............................................................0 – 400
Blows per minute
High .............................................................0 – 19,500
Low ..............................................................0 – 6,000
Overall length .................................................267 mm
Net weight (with battery cartridge) .................2.3 kg
Rated voltage .................................................D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
4
Explanation of general view
11 Speed change lever
12 Action mode changing ring
13 Arrow
14 Adjusting ring
15 Graduations
16 Tighten
17 Sleeve
18 Bit
19 Bit holder
20 Grip base
8413D
7.
8.
9.
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
21 Teeth
22 Side grip
23 Loosen
24 Depth rod
25 Thumb screw
26 Screw
27 Set plate
28 Limit mark
29 Brush holder cap
30 Screwdriver
8433D
14 mm
13 mm
36 mm
6 mm x 75 mm
6 mm
0 – 1,300
0 – 400
0 – 19,500
0 – 6,000
267 mm
2.4 kg
D.C. 14.4 V
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
Do not operate charger with damaged cord or
plug — replace them immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
8443D
16 mm
13 mm
38 mm
10 mm x 90 mm
6 mm
0 – 1,400
0 – 450
0 – 21,000
0 – 6,750
267 mm
2.6 kg
D.C. 18 V