Elektro-Automatik IF-U1 Benutzerhandbuch Seite 88

Programming
Explanation of some error codes:
Fehlercode
Hex. Dez. Beschreibung
Code 0x7: the object number used in the telegram is
1 1 RS232: Paritätsfehler
unknown to the device. This is because not all device types
2 2 RS232: Frame Error (Startbit o. Stopbit nicht erkannt)
use all object numbers.
3 3 Prüfsumme nicht korrekt
4 4 Startdelimiter falsch
Code 0x8: the length of the data field in the telegram is
5 5 CAN: max. Nodes überschritten
defined in the object list. This error code will be returned if
6 6 CAN: Node unbekannt/keine Gatewayfunktion
7 7 Objekt nicht definiert
a set value, which is always  bytes because of type „int",
8 8 Objektlänge nicht korrekt
should have been sent but the data field only contained one
9 9 Schreib-Leserechte verletzt, kein Zugriff
byte. Even if the start delimiter contained the correct telegram
0A 10 CAN: Gateway überlastet
0B 11 CAN: Gateway-Sendepuffer voll
length. This is a protection against setting wrong values.
0C 12 CAN: geteilte Message abgebrochen
Code 0x9: an object to set a set value has been sent, but the
0D 13 CAN: Messagebuffer überlaufen
0E 14 CAN: String-Startkennzeichen nicht korrekt
device is not in remote control mode. In this state you only
0F 15 Gerät ist in "Local" Modus
have read permission, but no write permission. You need to
10 16 CAN-Treiber-IC: Stuffing Fehler
set the device to remote control mode first.
11 17 CAN-Treiber-IC: CRC-Summenfehler
12 18 CAN-Treiber-IC: Übertragungsfehler
Codes 0xB/0xD/0x14: Messages are deleted from the
13 19 CAN: erwartete Datenlänge stimmt nicht
message buffer, if correctly executed. In case they come
14 20 CAN-Treiber-IC: Puffer voll
20 32 Gateway: CAN Stuffing Fehler
in too fast, this buffer will overflow and can not receive any
21 33 Gateway: CAN CRC-Summenfehler
more messages.
22 34 Gateway: CAN Übertragungsfehler
30 48 Obere Grenze des Objektes überschritten
Code 0xE: Strings have to be transferred differently when
31 49 Untere Grenze des Objektes unterschritten
using CAN. If the string length is greater than 8 characters,
32 50 Zeitdefinition nicht eingehalten
you have to use split messages that are designated with the
33 51 Zugriff auf Menüparameter nur bei "Ausgang aus"
string start tokens 0xFF, 0xFE etc. Also see 7.7.1.
34 52 Zugriff auf Sequenzsteuerelemente verweigert
36 54 Zugriff auf Funktionsdaten verweigert
Codes 0x30/0x31: these are related to set values. All set
37 55 Zugriff auf Sollwert verweigert (Gerät im Slavemodus)
values have an upper and a lower limit, which are defineable
Legende
at the PSI 9000 power supplies. The default upper limit for
Kommunikationsfehler
set values is 0x6400 and the lower limit is 0.
Userfehler
Interner Fehler
Limits also apply to time values.
Code 0x32: a time value using the wrong time range has
been sent. The upper or lower limits are not exceeded by
the value, but it still causes this error.
Codes 0x36/0x37: Conditions for the access to these data
are not fulfilled. See object list about the access conditions
in column 4.
© 009, Elektro-Automatik GmbH & Co. KG
Error code
Hex. Dec. Description
1 1 RS232: Parity error
2 2 RS232: Frame Error (Startbit or Stopbit incorrect)
3 3 Check sum incorrect
4 4 Start delimiter incorrect
5 5 CAN: max. nodes exceeded
6 6 CAN: node unknown/no gateway present
7 7 Object not defined
8 8 Object length incorrect
9 9 Read/Write permissions violated, no access
0A 10 CAN: Gateway overload
0B 11 CAN: Gateway send buffer full
0C 12 CAN: Split message aborted
0D 13 CAN: Message buffer overflow
0E 14 CAN: String identifier incorrect
0F 15 Device is in "local" mode
10 16 CAN driver chip: Stuffing error
11 17 CAN driver chip: CRC sum error
12 18 CAN driver chip: Form error
13 19 CAN: expected data length incorrect
14 20 CAN driver chip: Buffer full
20 32 Gateway: CAN Stuffing error
21 33 Gateway: CAN CRC check error
22 34 Gateway: CAN form error
30 48 Upper limit of object exceeded
31 49 Lower limit of object exceeded
32 50 Time definition not observed
33 51 Access to menu parameter only in standby
34 52 Access to sequence control denied
36 54 Access to function data denied
37 55 Access to set value denied (device is in slave mode)
Legend
Communication error
User error
Internal error
EN
88