Analogue Interface If-A1; Pin Assignment Of The Analogue Interface (5-Pole D-Sub Socket) - Elektro-Automatik IF-U1 Benutzerhandbuch

About the interface cards

4.4 Analogue interface IF-A1

4.4.1 Pin assignment of the analogue interface (25-pole D-Sub socket)
Pin Name Function
1 AI1 PSEL / RSEL
 AI3 CSEL
3 AI VSEL
4 AO3 PMON
5 AO1 VMON
6 AO CMON
7 DO1 CV
8 DO OVP
9 DO3 OT
10 DO4 Mains
11 DO5 Standby
1 DO6 CC
13 DO7 CP
14 AGND SEL
)
15
AGND
)
16
17 N.C.
18 AO0 VREF
19 +VCC
0
DGND
)
1
 DI1 SEL-enable
3 DI Rem-SB
4 Reserved
5 N.C.
1) Always related to the 10V end voltage, even if the voltage range is limitted
2) AGND and DGND are connected internally. AGND SEL at Pin 14 is inpedendent. It serves as reference for the difference amplifiers of all analogue inputs.
DIx, DOx, +Vcc are referenced to DGND. VREF, VMON, CMON, PMON are referenced to AGND. VSEL, CSEL und PSEL are referenced to AGND SEL.
3) Digital input, depending on the preset with the jumpers:
a) Setting High Range (high threshold): U
b) Setting Low Range (low threshold): U
4) Positive currents are flowing out of the device, negative currents are flowing into it.
© 009, Elektro-Automatik GmbH & Co. KG
Description
Analogue input:
Set value power / resistance
Analogue input:
Set value current
Analogue input:
Set value voltage
Analogue output:
Actual value power
Analogue output:
Actual value voltage
Analogue output:
Actual value current
Digital output:
Constant voltage operation
Digital output:
Overvoltage protection active
Digital output:
Overtemperature error
Digital output:
Mains voltage OK
Digital output:
Output off
Digital output:
Constant current operation „CC"
Digital output:
Constant power operation „CP"
Reference potential of the
analogue inputs
Reference potential of the
analogue outputs
Analogue output:
Reference voltage
Auxiliary voltage
(Reference: DGND)
Reference potential of the digital
ports
Digital input:
Switch-over to external interface
(else: local operation)
Digital input:
Output off
= 0V; I = -1.5mA, U = 1V; I = +0.7mA; U
in in
= 0V; I = -1.5mA, U = 1V; I = .mA, U
in in
Level
0..10V correspond to
0..100% von P / R
nom nom
0..10V correspond to
0..100% von I
nom
0..10V correspond to
0..100% von U
nom
0..10V correspond to
0..100% von P
nom
0..10V correspond to
0..100% von U
nom
0...10V correspond to
0..100% von I
nom
CV active = Low
CV not active= High
OVP = High
No OVP = Low
OT = HIGH
No OT = Low
Mains OK = Low
Mains not OK = High
Output off = Low
Output on = High
CC active = Low
CC not active= High
CP active = Low
CP not active = High
10V
1V...16V
Jumper set to „Low
Level":
SEL-enable on = Low
SEL-enable off = High
Jumper set to „Low
Level":
Output on = Low
Output off = High
= 4V; I = +4.5mA, Thresholds: U = < 5V; U
in Low
= 4V; I = +6mA, Thresholds: U = < 1V; U
in Low
Electrical specifications
Accuracy typ. < 0.1%
1)
Input impedance R > 5k
i
Accuracy typ < 0.1% at I
1)
Short-circuit-proof against GND
Quasi open collector with pull-up resistor
against VCC
I = -10mA at U = 0.3V
4)
max low
U = 0...30V
max
Short-circuit-proof against GND
Receiver: U < 1V; U
low high
Reference for SEL signals
Reference for MON signals and VREF
Accuracy typ < 0.1% , I
1)
max
Short-circuit-proof against GND
I = +50mA
4)
max
Short-circuit-proof against DGND
Reference for +VCC, control and
notification signals
Presettable input level (High/Low range):
1) U = < 1V ; U = > 4V or
Low High
) U = < 5V ; U = > 9V
Low High
Presettable logic level if input is not wired:
open = High Level or Low Level
= > 9V
High
= > 4V
High
EN
= +mA
4)
max
> 4V)
= + 8mA
4)
3)
60