Technical Specifications - Elektro-Automatik IF-U1 Benutzerhandbuch

About the interface cards
2. Technical specifications
General
Electrical isolation
Dimensions Type 1 (W x H x L)
Dimensions Type  (W x H x L)
Safety
EMI Standards
Overvoltage category
Operation temperature
Storage temperature
Relative humidity
IF-R1 / IF-R2 (RS232)
Connectors
Baud rates
Cable length
System Link Mode
(only with series PSI 9000)
└ Max. number of units
└ Bus termination
└ Patch cable
IF-U1 / IF-U2 (USB)
Connectors
Standard
Cable length
System Link Mode
(only with series PSI 9000)
└ Max. number of units
└ Bus termination
└ Patch cable
IF- C1 / IF-C2 (CAN)
Connectors
Baud rates
Bus termination
CAN standard
© 009, Elektro-Automatik GmbH & Co. KG
000V
4 x 80 x 100mm
4 x 80 x 45mm
EN 60950
EN61000-6-4,
EN 61000-6-,
EN 550 Class B
Class II
0...40°C
-0...70°C
<80% (w/o condensation)
1 x 9-pole D-Sub socket (f.)
 x RJ45 socket (not IF-R)
9600Bd, 1900Bd,
38400Bd, 57600Bd
depending on the baud rate,
up to 15m
yes
settable in the unit's menu
0.5m
1 x USB socket type A
x RJ45 socket (not IF-U)
USB 1.1
max. 5m
yes
settable in the unit's menu
0.5m
9-pole D-Sub socket (f.)
9- pole D-Sub socket (m.)
0kBd...1MBd in steps
settable in the unit's menu
V.0 part A
IF-A1 (Analogue)
Connectors
Analogue inputs:
Input voltage range
Maximum range
Nominal range
Input impedance
Resolution
VSEL, CSEL, PSEL (RSEL)
Relative error
VSEL, CSEL, PSEL
RSEL (Option)
Response time
1)
Analogue outputs:
Nominal output voltage range
VMON, CMON, PMON
I max. at 10V
out
VREF
I max. at 10V
out
Resolution
VMON, CMON, PMON, VREF
Relative error
VMON, CMON, PMON, VREF
Settling time of the analogue outputs
Auxiliary voltage
Current max.
Digital outputs:
Typ e
30
Output current
Maximal
Nominal
Output voltage
High
Low
Response time
)
Digital outputs:
Input voltage
Maximum range
if set to: Level=LOW
U
Low
30
U
High
if set to: Level=HIGH
U
Low
U
High
In order to calculate the total response time of a step change, from an analogue
1
interface input to the power output you need to add the response time of the device
to this time.
Time between occurence of the event, which is about to be notified, and the mo-

ment the notification is executed.
EN
5-pol D-Sub socket(f.)
-5V...+15V
0V...10V
25kΩ
< mV
0.1%
0.5%
< 4ms
0V...10V
mA
1V...10V
10mA
< mV
0.1%
< 4ms
1...15V
50mA
pull-up resistor to +15V
I = -0mA
max
at U = 0.5V
out
1...10mA
+15V
< 0.3V
< 4ms
-5V...+30V
< 1V
> 4V
< 5V
> 9V
...continued
56