Kettler 7992-600 Montageanleitung Seite 3

GB Assembly Instructions
Before assembling or using the ergometer, please read the following instructions carefully. They contain important in-
formation for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a
safe place for maintenance purposes or for ordering spare parts.
For Your Safety:
The Ergometer should be used only for its intended purpose,
i.e. for physical exercise by adult persons.
Any other use of the equipment is prohibited and may be dan-
gerous. The manufacturer cannot be held liable for damage or
injury caused by improper use of the equipment.
The Ergometer has been designed in accordance with the lat-
est standards of safety. Any features which may have been a
possible cause of injury have been avoided or made as safe as
possible.
The unit requires a power supply of 220-230 V/50 Hz. It
should be connected only to a safety socket with a single 10-A
fuse. Before commissioning the appliance pay attention to the
fact that the correct plug-in power supply unit (observe mark-
ing) has been connected properly. Do not under any circum-
stances carry out electrical repairs or alterations yourself. Al-
ways ensure that such work is done by a properly qualified
electrician.
Important: disconnect the apparatus from the mains before
doing repair, maintenance or cleaning work.
Incorrect repairs and structural modifications (e.g. removal or re-
placement of original parts) may endanger the safety of the user.
In case of enquiry, please contact your KETTLER dealer.
Damaged components may endanger your safety or reduce the
Handling the equipment
Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust.
The Ergometer is designed for use by adults and children
should not be allowed to play with it. Children at play behave
unpredictably and dangerous situations may occur for which
the manufacturer cannot be held liable.
The Ergometer complies fully with DIN EN 957 - 1/5, class A. It
is therefore suitable for therapeutic purposes.
Instructions for Assembly
Ensure that you have received all the parts required and that
they are undamaged. Should you have any cause for com-
plaint, please contact your Kettler dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters, and in
some cases you are referred to a more detailed explanation
(see below).
The equipment must be assembled with due care by an adult person.
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
List of spare parts page 11
When ordering spare parts, always state the full article number,
spare-part number, the quantity required and the inspection num-
ber stamped on the back.
Example order: Art. no. 7992-600/spare-part no.
pieces/inspection no......
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words "with
fastening material".
lifetime of the equipment. For this reason, worn or damaged
parts should be replaced immediately and the equipment taken
out of use until this has been done. Use only original KETTLER
spare parts.
If the equipment is in regular use, check all its components thor-
oughly every 1–2 months. Pay particular attention to the tightness
of bolts and nuts. This applies especially to the securing bolts for
saddle and handlebars. The brake tension should also be
checked at regular intervals and adjusted as necessary. This ap-
plies especially to the securing bolts for saddle and handelbars.
Instruct persons using the equipment (in particular children) on
possible sources of danger during exercising.
Before beginning your program of exercise, consult your doc-
tor to ensure that you are fit enough to use the equipment. Base
your program of exercise on the advice given by your doctor.
Incorrect or excessive exercise may damage your health.
Before beginning your program of training, study the instruc-
tions for training carefully.
Possibly occurring noise during reverse pedalling result from
engineering and are absolutely safe.
Our products are subject to a constant innovative quality as-
surance. We reserve the right to perform technical changes re-
sulting therefrom.
On principle, the equipment does not require any special main-
tenance. All bearings have a lifetime lubrication or require lit-
tle maintenance.
Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment.
Ensure that no liquids penetrante the interior of the Ergometer.
The ergometer has a electric brake system operating indepen-
dent of speed which is maintenance - free and does not require
any adjusting work.
The Ergometer works independent of revolutions per minute.
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary
structed. The required tools are supplied with the equipment.
Bolt all the parts together loosly at first. Do not tighten any of the
bolts until the assembly operation has been fully completed.
For technical reasons, we reserve the right to carry out prelim-
inary assembly work (e.g. addition of tubing plugs).
To pull off the pedal arms screw a bolt M 12 (it's not supplied
by the manufacturer) into the threaded opening after removing
the protective cap and bolt.
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary
/ 2
10100030
KETTLER (GB) Ltd. · Kettler House, Merse Road · North Moons Moat · Red-
ditch, Worcestershire · B98 9HL · Great Britain
KETTLER International Inc. · 1355, London Bridge Road · USA-Virginia
Beach, Virginia 23450
http://www.kettler.net
3