Product Description And Specifications - Bosch PSB 500 RE Originalbetriebsanleitung

OBJ_BUCH-1750-001.book Page 11 Wednesday, August 1, 2012 1:55 PM
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Technical Data
Impact Drill
Article number
Rated power input
Output power
No-load speed
Rated speed
Impact rate
Rated torque
Torque at max. output power
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Bosch Power Tools
Intended Use
The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal and plastic. Ma-
chines with electronic control and right/left rotation are also
suitable for screwdriving and thread-cutting.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Key type drill chuck
2 "Drilling/Impact Drilling" selector switch
3 Lock-on button for On/Off switch
4 On/Off switch
5 Rotational direction switch
6 Button for depth stop adjustment *
7 Wing bolt for adjustment of auxiliary handle *
8 Auxiliary handle (insulated gripping surface)*
9 Depth stop*
10 Handle (insulated gripping surface)
11 Chuck key
12 Universal bit holder*
13 Screwdriver bit*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
PSB 500 RE
3 603 A27 0..
W 500
W 260
-1
min 50 – 3000
-1
min 2400
-1
min 48000
Nm 1.1
Nm 7.5
mm 43
mm 10
mm
mm 25
mm 2 – 13
kg 1.6
/II
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
Drilling into metal: a =4.0 m/s
h
Impact drilling into concrete: a
Screwdriving without impact: a
2
Tapping: a <2.5 m/s , K=1.5 m/s
h
English | 11
PSB 530 RE
3 603 A27 0..
530
260
50 – 3000
2400
48000
1.1
7.5
43
10
8 8
25
2 – 13
1.6
/II
2 2
, K=1.5 m/s ,
2 2
=33.0 m/s , K=3.5 m/s ,
h
2 2
<2.5 m/s , K=1.5 m/s ,
h
2
.
2 609 006 496 | (1.8.12)