Smeg KDR 35 X Montageanweisung Und Gebrauchsanweisung Seite 16

• Carry out all the masonry work necessary (e.g.
installation of an electric socket and/or a hole for the
passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
Additional warning instructions on installation procedure:
• Check that electric cables are not damaged.
Remove AND CONSERVE the screws that temporarily fix
the flue units (for reasons of transport), the hood or the
flue unit with the suction unit. The two parts should be
disassembled to facilitate installation.
Check how the parts are fixed together to repeat
assemblage at the opportune moment (see also fig. 6 and
operation 17).
1. Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre.
installation.
2. Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must
correspond to the centre line drawn on the wall, and the
bottom edge of the drilling template must correspond to
the bottom edge of the hood: bear in mind that, when
installation is complete, the underside of the hood must
be at least 50 cm above the cooker top in the case of
electric cookers, and at least 75 cm above the cooker top
in the case of gas or mixed cookers.
3. Rest the support bracket on the drilling template so that it
coincides with the dotted rectangle, mark the two outer
holes and drill them (mark and also carry out upper drill
holes - 3a), remove the drilling template, insert 4 wall
plugs and fix the hood support bracket into place using
two 5x45mm screws.
4. Hang the hood on the bracket.
5. Adjust the distance of the hood from the wall.
6. Adjust the horizontal position of the hood.
7. Remove the carbon filter frame (see also Fig. 3); mark
the drill hole, using a pencil, for fastening the hood to the
wall.
8. Remove the hood from the bracket.
9. Drill at the point marked (Ø8mm - see operation 7).
Insert 1 wall plug.
10. Rest the chimney support bracket „G" against the wall,
touching the ceiling. Use the support bracket as a drilling
template (the small slot formed on the support must
coincide with the line drawn on the wall as above –
operation 1) and mark 2 holes with a pencil, dril the holes
(Ø8mm), insert 2 wall plugs.
bracket to the wall using two 5x45mm screws.
11. Hook the hood onto the bottom bracket.
12. Fasten the hood to the wall with 1
(ABSOLUTELY NECESSARY), remount the carbon filter
frame (see also Fig. 3).
13. Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the
This will facilitate
Fix the chimney support
5x45 mm screw
connection ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the
fumes to the outside. If the hood is to be used in filter
version, fix deflector „F" to the chimney support bracket
„G" using 1 screws, and connect the other end of the pipe
to the connection ring on deflector „F".
14. Make the electrical connections.
15. Insert the external covering, of the motor group, half-way.
16. Make all the electrical connections between the two parts
(for major safety during this operation you may fix the
motor group to the external covering with one screw).
17. Insert the external covering of the motor group fully and
permanently fix with 6 screws.
18. Fix the bracket Z with two screws, so that the bracket
blocks the lower section of the telescopic chimney
(external covering) to the wall.
19. Apply the chimney stacks and fasten them at the top to
the chimney support „G" (19b) using 2 screws (19a).
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.
16