Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Allgemeiner Teil / General Section
LNC SETUP
TYPE
POWER
-
A 09 . 750
~
A 09 . 750
-
B 09 . 750
~
B 09 . 750
PRESS OK OR
LNC SETUP
TYPE
POWER
-
A 09 . 750
~
A 09 . 750
-
B 09 . 750
~
B 09 . 750
PRESS OK OR
46
46
1 - 16
LNC SETUP
__________________________________________________________________________
The LNC SETUP sub-menu
If this satellite receiver is operated on an aerial system for multiple satellite
reception, it must first be adjusted to the satellite aerial and the LNC configu-
ration used.
In order to tune the receiver as finely as possible to the various aerial
installations, 6 LNC arrangements are available for the SAT input.
Depending on the LNC arrangement selected, varying switching signals are
emitted when changing to other channel positions (22 kHz, mini DiSEqC,
DiSEqC 1.0) in order to select the LNC required for reception and its frequency
range.
The oscillator frequency of the LNC used must be entered.
The number of possible oscillator frequencies will depend on the LNC
arrangement chosen.
1
Call up the » INSTALLATION« sub-menu by pressing the »
followed by »2«.
2
Call up the » LNC SETUP« sub-menu by pressing »1«.
– » 2« flashes (this is the type of the set LNC arrangement).
2
ON
Key to menu items:
TYPE
POWER
–
I
A 09 . 750
~
A 09 . 750
OK
I
LNC SETUP
__________________________________________________________________________________
The satellie receiver is pre-programmed for the following LNC oscillator
frequencies:
– A (22 KHz off) 09 . 750 GHZ
~
A (22 KHz on) 09 . 750 GHZ
– B (22 KHz off) 09 . 750 GHZ
~
B (22 KHz on)
3
Use the
»;
»1« to »6 «.
Note:
The LNC voltage supply is switched on as factory setting. The receiver
supplies power to the satellite aerial.
If your receiver is connected together with other satellite receivers to a joint
aerial (a so-called single cable solution in the master distribution), you will
need to switch off the LNC voltage supply.
Select »POWER« then use the
4
again.
2
Note:
ON
If you use an LNC with another or several oscillator frequencies, you can
change the frequency. For example, for the reception of the Astra Programme
Magyar 2 and ERT satellites (channel positions 108/109), the oscillator
frequency is to be set to 10.600 GHz.
I
If you are using a number of LNCs, all the oscillator frequencies will need to
be checked and, if necessary, "re-entered".
5
Use the
».
then enter the new frequency directly using the »
use the
»;
6
Press»OK« to save the setting.
– The »INSTALLATION« sub-menu appears on the picture screen.
Press »
« as often as required to exit the menu.
7
i
LNC arrangement, type 2 is set.
2
LNC voltage supply on.
ON
Satellite A selected, LO frequency of LNC
without 22 kHz switching signal.
Satellite A selected, LO frequency of LNC
with 22 kHz switching signal.
Save all settings.
End settings without saving.
– C (22 KHz off) 09 . 750 GHZ
~
C (22 KHz on)
– D (22 KHz off) 09 . 750 GHZ
~
09 . 750 GHZ
D (22 KHz on)
or :« button to select the required LNC arrangement type
»;
or :« button to select »OFF« or » ON«
or ,« button to select the oscillator frequency to be changed
1 ... 0
or :« button to change the frequency step by step.
« button twice
i
45
45
09 . 750 GHZ
09 . 750 GHZ
« buttons, or
GRUNDIG Service
STR 8150
Werbung
Inhaltsverzeichnis
