Channel Setup - Grundig STR 8150 Serviceanleitung

STR 8150
NAME
CH.
LNC
POL
GHZ
VIDEO
CONT.
PRESS OK OR
NAME
CH.
LNC
POL
GHZ
VIDEO
CONT.
PRESS OK OR
36 36
GRUNDIG Service

CHANNEL SETUP

The »CHANNEL SETUP« sub-menu
This satellite receiver is already pre-programmed for the current channels of
many satellites. In most cases, no correction will be required.
However, new channels are continuously being added, or transmission frequen-
cies being changed. The current status of the transmission frequencies can be
called up via the Teletext pages of various channels (e.g. SAT 1 or 3SAT), or can
be found in a current satellite TV magazine.
You can then programme these channel positions in the "CHANNEL SETUP"
sub-menu and you will have access to the image and sound settings of the
individual channel positions.
1 Use the
setup of which you wish to change, or select a not programmed channel
position if you wish to set up a new satellite channel.
2 Call up the » CHANNEL SETUP« sub-menu by pressing »
by »3«.
3
Call up the » TUNING« sub-menu by pressing »1«.
. . ZDF . . .
– The channel position number, e.g.
002 AUDIO
STEREO
is flashing.
1– A 7 . 02 7 . 20
H PANDA BW1
10 . 964 RADIO OFF Key to menu items:
16 : 9 OFF
NAME
NORM. LOCK OFF
1 DEC . OFF CH. 002
I
LNC
LNC
POL
GHZ
VIDEO
CONT.
Continued on next page.
CHANNEL SETUP
AUDIO STEREO
7.02 7.20
PANDA B 1
. . ZDF . . .
002 AUDIO
RADIO OFF
STEREO
1– A 7 . 02 7 . 20
H PANDA BW1
16 : 9
10 . 964 RADIO OFF
16 : 9 OFF
LOCK
NORM. LOCK OFF
DEC.
1 DEC . OFF
I
OK
I
Note:
It is not allowed to change the channel position number in the sub-menu, e.g.
» CH. 002 «, otherwise the data of the last selected channel position would
be copied into the current channel position.
Copying is explained on page 40, section "Copying a channel position".
It is not possible to switch the channel position in the sub-menu.
Even if a "FAVOURIT ES" channel index has been selected, the channel position
number of the last selected channel is shown in the "NORMAL"
channel index. Channel settings can only be changed in the "NORMAL"
channel index.
Use ».
Use »1 ... 0
settings.
Use the »
If the picture quality is very poor, the set is switched automatically to blue
background.
4 The channel position number, e.g. »002 «, is flashing to the right of »CH.«;
please do not change this.
____________________________________________________________
». ,« or »1 ... 0 « button to select the channel position the
»0 02«, of the " NORMAL " channel index
. . ZDF. . . Name of the selected channel.
Number of the channel position.
Satellite selection 1– A or (B ,C,D)
1 – A
(– : 22 kHz switching signal off).
~
~
Satellite selection 1 A oder (B ,C,D)
1 A
~
( : 22 kHz switching signal on ).
Vertical or horizontal polarization.
H
10 . 964 Transmission frequency of the selected channel.
Normal or inverse video modulation.
NORM.
1 Contrast level 1 or 2
_______________________________________________________________________
Audio mode stereo (or mono or two-channel sound).
Left/right sound frequency carrier.
De-emphasis/noise reduction PANDA, 50µs, J17,
audio bandwidth B 1, B 2, B 3 or B 4
With »RADIO ON«, the picture screen background is
displayed in blue.
OFF Picture format of TV set (ON = 16:9, OFF = 4:3).
Channel position not locked.
OFF
OFF Decoder function off.
Save all settings.
End settings without saving.
or ,« to select the setting to be changed.
« to enter values directly, or use »;
TXT « button to switch between TV picture and blue background.
Allgemeiner Teil / General Section
« twice followed
i
35 35
or :« to select other
1 - 13