Unpacking The Appliance; Electric Connection - Clatronic AE 3666 Bedienungsanleitung

Unpacking the appliance

1. Remove the appliance from its packaging.
2. Remove all packaging materials like foils, filling materials,
cable holders, and carton packaging.
3. Check the scope of deliveries for completeness.
NOTE:
There may still be dust or production remains on the
appliance.
We recommend that you clean the appliance as described
under "Cleaning".
NOTE:
Remove the cardboard disk insert from the inside of the
filter / blade unit (4) before starting the motor.
Description of the Parts
1 Pusher
2 Chute
3 Lid
4 Filter / Blade
5 Receptacle
6 Fold up spout
7 Drive wheel (not detachable)
8 Locking bar with safety switch
9 Base with motor
10 On / off speed control (I / 0 / II)
11 Pulp collector
Setting up of the appliance
For assembly, also refer to the illustrations on page 3.
1. Set the appliance so that the speed controls (10) point
towards you.
2. Tilt the locking bar (8) to the right.
3. Attach the receptacle (5) on top of the base casing. The
base casing (9) has a recess. Here the spout (6) of the
receptacle casing (5) must be placed.
WARNING risk of cuts!
The filter / blade (4) is sharp!
4. Place the filter / blade (4) on top of the drive wheel. Press
it down. It clicks in place on the drive wheel.
5. Check the filter / blade (4)! Feel under the filter edge. It
should not loosen under slight tension.
6. Attach the pulp collector (11) on the left side. To do so,
hold it slightly sideways to press the upper edge into the
shroud of the receptacle casing (5).
7. Attach the lid (3). It reaches all the way over the pulp
collector (11).
NOTE:
Your appliance is equipped with a safety switch. It
prevents accidental motor start. Check the correct
locking of the locking bar (8).
8. Lock the locking bar (8) over the lid (3).
32
9. Press the spout (6) downwards to open the flow of the juice.
10. Place the juice jug to the right of the appliance.
11. Ensure that the speed control (10) is set to "0" position.

Electric Connection

• Before inserting the power plug into the outlet, check
that the mains voltage to be used matches that of the
appliance. You can find the required information on the
nameplate.
• Connect the appliance only to a correctly installed safety
socket.
Operation
Speed control settings
• Select setting "I" for smaller fruit like strawberries.
• Select setting "II" for larger pieces or hard vegetables, for
example carrots.
Preparations
• Wash the fruit to be processed.
• Cut the fruit in pieces to fit through the chute opening (2).
• Remove large pips and stems.
Extracting Juice
NOTE:
The appliance is intended for short-term use. After opera-
ting it for 6 minutes, take a 5 minute break.
WARNING:
• Check all accessories again for proper attachment before
switching the appliance on.
• Ensure that the spout is pressed downwards.
NOTE:
Remove the cardboard disk insert from the inside of the
filter / blade unit (4) before starting the motor.
1. Set the speed control (10) to the desired position. The
motor starts running.
2. Insert the fruit pieces in the chute opening (2) and push
them down with the pusher (1). Please note! The pusher
(1) has a guide way in the filler opening.
3. The juice flows out at the right side of the casing. The pulp
is collected in the pulp collector (11). If there is an exces-
sive discharge of juice, switch the speed control (10) to
setting "I" and exert less pressure on the pusher (1).
NOTE:
• Observe the juice jug. Stop operation in time to prevent
overflowing.
• Berries and citrus fruits (such as gooseberries, grapes,
oranges) are usually not juiced but pressed.
• When juicing these fruits with their high juice content,
splashing of juice from the area of the pulp collector (11)
may occur. In this case, we recommend that the pulp
collector (11) is emptied more frequently.