Inhaltsverzeichnis
Werbung
Operating Hints
This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in
the relevant spare parts list.
CONTROLS
GB
MODE
REP . 1
HOLD
PROG
STOP
RAND
PREV.
INTRO
Batteries
PLAY
The display indicates:
PROG:
during programming or programme
: flashing: the batteries are weak;
playback
continuously: the battery voltage is too low
88
RAND:
during the RANDOM function
:
track number
INTRO:
during the INTRO function
playing time
88:88:
REP.:
during the REPEAT function:
REP. 1 – repeat one
:
when DAS is activated
HOLD:
when HOLD is activated
CD PLAYER
Inserting a CD
• Open the lid by pressing both PUSH OPEN
buttons and lifting the lid gently.
• Insert an audio CD, printed side up.
• Push gently on the CD center so that it fits onto
the hub.
• In addition to standard 12 cm CD's, you can
also play 8 cm CD singles without an adapter.
• Close the lid by pushing it gently on its right-hand
side.
• Press PLAY to start playback.
– The CD-player scans the contents list of the CD.
The total playing time and the total number of
tracks appear on the display.
• After that, the CD starts playing.
Removing the CD:
• To take out the CD, open the CD lid by pressing
both PUSH OPEN buttons and lifting the lid gently.
• Hold the CD by its edge and press the hub
gently.
• Open the CD door only if the CD player is in
position STOP.
Playing a CD
• Press PLAY to start playback.
– The display shows the current track number and
its elapsed playing time.
• Adjust the sound using the VOLUME and UBS
controls.
• For brief interruptions, press PLAY.
– The playing time indication starts flashing.
• To resume playback, press PLAY again.
DAS / HOLD
DAS – Digital Anti shock System
PUSH
REPEAT/
OPEN
The DAS memory stores the CD data (music) for 10
SET
seconds in advance in order to prevent interruption
DC 4.5V
NEXT
during play caused by shock and vibration.
+>-
• Activate the DAS memory by pressing the DAS
button once.
– The Anti Shock symbol
UBS
in the display starts
filling, the display
shows for example:
PHONES
– The state of the DAS symbol in the display changes
according to the state of the DAS memory.
DAS
• To disable this function, press the DAS button once
more.
Note: When switching the DAS feature on and off,
VOLUME
CD play will be delayed or interrupted for a short time.
• As the Digital Anti shock System requires more energy,
HOLD
it is advisable to switch it off when the playing
conditions are good, in order to save battery life.
Hold function
• Set the HOLD switch to the
0
position.
PUSH
– The 'HOLD' indication
HOLD
OPEN
lights up on the
display.
– Now, the CD player buttons will not operate.
• To disable this function, set the HOLD switch to the
position.
0
– The 'HOLD' indication disappears from the display.
Note: Even when the HOLD switch is in the
0
position,
it is still possible to start playback with the PLAY button.
To avoid inadvertent battery consumption, please
make sure that there is no CD in the compartment
when travelling, etc..
• To stop playback, press STOP.
– The total playing time and number of tracks will
then appear on the display.
• If you press the STOP button again, you will
switch off the set.
– If no button is pressed for 30 seconds, the set will
switch off automatically.
– The CD player also goes to position STOP:
– by opening the CD lid;
– when the end of the CD is reached;
– if the batteries run down or if the power supply
is interrupted.
Prev. / Next
Selecting another track during play
• Press PREV. or NEXT until the required track
number appears in the display.
– The selected track begins to play.
Starting with a particular track
• Press PREV. or NEXT until the required track
number appears in the display.
• Press PLAY.
– Play starts from the selected track.
Searching for a passage during play
• Hold PREV. down to search backwards to the
beginning.
• Hold NEXT down to search forwards to the end.
Note: This function can be described as 'audibly'
searching for a title.
During the search, volume is reduced and returns to
its adjusted level as soon as the button is released.
POWER SUPPLY
Batteries
• Open the battery compartment and insert as
indicated two alkaline batteries type LR6,UM3,
AA or insert two rechargeable Nickel-Cadmium
batteries .
•
• Remove the batteries if they are empty or if the
CD player is not to be used for a long time.
The display indicates when the battery voltage is
too low:
• When the indicator
flashes, the batteries are
getting too weak.
• When
appears continuously, the battery
voltage is too low and the CD player will soon
shut down.
Note on Environmental Protection
Note:
The battery supply is switched off when the
Do not throw exhausted batteries in
DC IN 4.5 V socket is in use.
the household refuse.
When changing over to battery supply, pull out the
Hand over the old batteries to your
plug from the DC IN 4.5 V socket.
dealer or public collecting points when
buying new ones.
Mains adapter (supplied)
1 Make sure that the local voltage corresponds to
the voltage of the adapter.
2 Connect the supplied mains adapter (4,5 V/700 mA
DC 4.5V
+>-
Direct Current plus-pole to the centre pin) to the
player's DC IN 4.5 V jack and to the wall outlet.
• Always disconnect the adapter if you are not
using it.
Note:
The CD-player remains connected to the mains
even when it is switched off.
The unit is only fully isolated from the mains if the
mains adapter is removed from the wall socket.
CD PLAYER
Selecting a different playback mode
The MODE button allows you to select five different
playback modes.
• Press the MODE button until the display shows the
desired function:
1 INTRO: only the first 10 seconds of each title are
PROG
played; after the last title, the CD player stops.
2 SINGLE: only the selected track is played, then the CD
PROG
player stops.
3 RANDOM: the tracks are played in random order until
all of them have been played once; then, the CD
player stops.
4 PROGRAM: to enter the programming mode (see
'Programming').
INTRO
1
5 No indication: normal playback.
• If you select RANDOM during playback, the function
starts from the end of the current track.
• The INTRO and RANDOM functions are not possible
RAND
during playback of a programme.
PROG
• To go back to normal playback, press MODE
repeatedly until all the mode indications disappear.
• You can also press STOP twice to switch the set off.
Repeat function
• Press the REPEAT/SET button during playback to
switch this function on and off.
– The CD is played continuously.
You can use the REPEAT function together with the
MODE button to obtain different combinations of
repeated playback.
• Press REPEAT/SET, then press the MODE button to
select the desired playback mode :
REPEAT
–> REPEAT INTRO –> REPEAT
only
SINGLE –> REPEAT RANDOM –> REPEAT
PROGRAM –> REPEAT
only
, etc..
Recharging Nickel-Cadmium batteries
(only AA IEC KR 15/51)
Your mains adapter also works as a charger.
This is only possible with Ni-Cd batteries with the
reference AA IEC (KR 15/51) 1.2 V/600mA.
Note:
As a quick reference when buying the Ni-Cd batte-
ries, be sure that the metal cap on the negative pole
is exposed more than 3 mm as illustrated.
• Charge the batteries prior to first use and also if
3 mm
min
the batteries have not been used for a long
period.
• Install the rechargeable batteries in the battery
compartment as described before.
• Connect the adapter to the CD-player and then
to the wall outlet.
• The batteries should be allowed to recharge for 8
hours for full capacity.
• The ambient temperature for recharging should
be between 0˚C and 40˚C.
• The player can be operated while the batteries
are being recharged.
Automatic Power-Off
This CD-player is equipped with an automatic
power-off function.
• In STOP mode, the player automatically shuts
down approximately 30 seconds after the last
operation.
• If you press STOP while the set is in STOP mode,
the player also shuts down.
• To reactivate the player, press PLAY.
Programming
By programming the player you can play up to 20 tracks
in any desired order.
Storing a programme
• Insert a CD and close the compartment.
• Press the MODE button repeatedly until the 'PROG'
indication starts flashing on the display.
• Select the first desired track using PREV. or NEXT.
– The selected track number flashes.
• Store this track by pressing REPEAT/SET.
• Select and store in this way all desired titles.
• You can leave the storing mode by pressing PLAY or
STOP.
Checking the programme
• In STOP mode, press PREV. or NEXT repeatedly.
– The display shows in sequence all programmed track
numbers.
Playing the programme
• Press PLAY.
– Play starts with the first track of the programme.
– The display shows 'PROG'.
– After the last track playback stops. The total playing
time and total number of tracks will then appear on the
display.
Note: While playing a programme, it is possible to use
PREV. or NEXT to select the desired programmed tracks.
Erasing a programme
The contents of the memory will be erased:
– when you switch off the player;
– if the batteries become exhausted or if the power
supply is interrupted in another way.
Werbung
Inhaltsverzeichnis
