EINHELL 41.377.55 Originalbetriebsanleitung Seite 13

Anleitung_DTA_25_2_SPK7:_
The value given for vibration is an equipment-based
characteristic value and does not represent the
impact on the hand and arm system when the
equipment is used. The impact on the hand and arm
system when the equipment is used will depend, for
example, on the force of the grip, the pressing force,
the direction in which you are working, the air
pressure setting, the workpiece and the workpiece
support.
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Wear gloves.
Compressed air quality:
Purified and with oil mist.
Air supply:
Via a conditioning unit with filter pressure reducer and
mist oiler connected to a compressed air source.
Recommended capacity of the compressor:
Compressor with a capacity of approx. 250 l/min,
which is the equivalent of engine power of approx. 2.2
kW
Remember:
Wear the necessary protective clothing when
working with the stapler, in particular safety
goggles.
Pay attention to the safety regulations.
6. Starting up
Each time before starting work, check that the
trigger catch functions perfectly and that all
screws and nuts are securely fastened.
Never tamper with the stapler.
Never dismantle or block any parts of the stapler
such as, e.g. a trigger catch.
Never carry out any "emergency repairs" with
unsuitable means.
Proper stapler maintenance is required at regular
intervals in accordance with the information
supplied by the manufacturer.
Take precautions to prevent anything which
would weaken or damage the equipment, e.g.
from
07.09.2011 13:33 Uhr Seite 13
a) striking or engraving,
b) modifications which are prohibited by the
manufacturer,
c) guiding on templates made of hard material, e.g.
steel,
d) pushing across the floor,
e) using as a hammer,
f) any kinds of acts of violence.
6.1 Checking the trigger catch
Check the trigger catch (Fig. 1/Item H) each time
before use. The trigger catch must move freely
without catching. The spring on the trigger catch must
return the trigger catch to the released initial position.
Never use the equipment if the trigger catch is not
working.
1. Disconnect the equipment from the air supply.
2. Remove the staples/nails from the magazine (Fig.
1/Item E).
3. Check that the trigger and the trigger catch can
move up and down freely.
4. Connect the equipment to the air supply.
5. Press the trigger catch against the workpiece
without pressing the trigger. The equipment
should not operate. Never use the equipment if it
operates without the trigger being pressed. Risk
of injury.
6. Remove the equipment from the workpiece. The
trigger catch must return to the released initial
position. Press the trigger. The equipment should
not operate. Never use the equipment if it
operates. Risk of injury.
7. Press the trigger and press the trigger catch
against the workpiece. The equipment operates.
8. Press the trigger catch against the workpiece and
press the trigger; the equipment operates.
6.2 Loading staples and nails
When you fill the magazine (Fig. 1/Item E), make
sure that you hold the equipment in such a way
that the muzzle is pointed neither at you or
anyone else.
To fill the magazine, press the magazine lever
(Fig. 1 / Item C) and slide back the magazine
cover (Fig. 1 / Item D) as far as it will go.
Insert the staples as shown in (Fig. 3) or the nails
as shown in (Fig. 4).
Do not insert more than one complete stick of
staples/nails, otherwise the magazine will be
overfilled and you will not be able to close it
again. Slide the magazine cover forward again
until it snaps into place.
The level indicator (Fig. 5 / Item F) shows the
number of loaded staples / nails if less than 50
are loaded.
GB
13