Operating Elements And Connections; Safety Notes - IMG STAGE LINE DJP-104USB Bedienungsanleitung

DJ HiFi Turntable
with USB Interface
These instructions are intended for users
without any specific technical knowledge .
Please read these instructions carefully prior
to operating the unit and keep them for later
reference .
All operating elements and connections
de scribed can be found on the fold-out
page 3 .
1 Operating Elements
and Connections
1 Adapter for single records
2 POWER switch
3 Stroboscope lamp
4 Start / Stop button
5 Counterweight for the tone arm
6 Rotary knob for the antiskating adjust-
ment
7 Lever for the tone arm lift
8 Tone arm locking lever
9 Tone arm
10 Sliding control PITCH ADJ . to change the
pitch (±16 %)
11 Headshell with phono cartridge system
12 Button for the speed 45 rpm
13 Button for the speed 33
14 Selector switch PHONO / LINE for the audio
level of the analog audio output (18)
PHONO
for connection to a phono input
LINE
for connection to a line input
15 Control GAIN for the audio level at the
USB connection (16)
16 USB connection (type B) for connecting
a computer
17 Mains plug for connection to 230 V/ 50 Hz
18 Phono plugs for the analog audio output
for connection to a line input or phono
input, e . g . of an amplifier or mixer
(red = right channel, white = left channel)

2 Safety Notes

This unit corresponds to all relevant directives
of the EU and is therefore marked with
WARNING The unit uses dangerous mains
voltage . Leave servicing to
skilled personnel only . Inex-
pert handling or modification
of the unit may result in electric
shock .
•
The unit is suitable for indoor use only . Pro-
tect it against dripping water and splash
water, high air humidity, and heat (admis-
sible ambient temperature range 0 – 40 °C) .
•
Do not place any vessels filled with liquid,
e . g . drinking glasses, on the unit .
•
Do not operate the unit and immediately
disconnect the plug from the mains socket
6
1 . if there is visible damage to the unit or
to the mains cable .
2 . if a defect might have occurred after the
unit was dropped or suffered a similar
accident .
3 . if malfunctions occur .
In any case the unit must be repaired by
author ized personnel .
•
A damaged mains cable must be replaced
by skilled personnel only .
•
Never pull the mains cable to disconnect
the mains plug from the socket, always
seize the plug .
•
No guarantee claims for the unit and no li-
ability for any resulting personal damage or
material damage will be accepted if the unit
is used for other purposes than originally
intended, if it is not correctly connected,
operated, or not repaired in an expert way .
•
Important for U. K. Customers!
The wires in this mains lead are coloured
in accord ance with the following code:
blue = neutral
brown = live
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying the
terminals in your plug, proceed as follows:
1 . The wire which is coloured blue must be
connected to the terminal in the plug
which is marked with the letter N or
coloured black .
⁄ rpm
1
3
2 . The wire which is coloured brown must
be connected to the terminal which is
marked with the letter L or coloured red .
If the unit is to be put out of oper-
ation definitively, take it to a local
recycling plant for a disposal which
will not be harmful to the environ-
ment .
3 Applications
The turntable DJP-104USB is suitable both
for private application and for professional
DJ operation . It is equipped with a phono
preamplifier and can there fore also be con-
nected to a line input .
To digitalize the music of records, the
DJP-104USB can be connected to a com-
puter via the USB interface . In addition, an
audio recording software is required . Different
programmes are avail able as freeware on the
.
Internet .
4 Assembly and Basic Settings
After unpacking all parts, the packing material
should be kept for a possible transportation .
Place the turntable on an even, horizontal
surface and place the supplied felt slipmat
on the turntable platter .
4.1 Adjusting the stylus pressure
1) First turn the antiskating knob (6) counter-
clockwise to "0" .
2) Pull off the protective cover of the stylus
in a downward movement .
3) Place the lever for the tone arm lift (7) in
the front position .
4) Open the tone arm locking lever (8) to the
right . Seize the handle of the tone arm and
lead it carefully just before the turntable
platter so that it can freely be moved up-
wards and downwards .
Attention! The stylus must not hit against
anything .
5) Lead the tone arm with the left hand to the
side so that the stylus does not hit against
the turntable platter . With the right hand
turn the counterweight (5) so that the
tone arm remains exactly in a horizontal
position and does not move upwards or
downwards (fig . 3) .
– If the tone arm moves upwards: turn the
counterweight counter-clockwise .
– If the tone arm moves downwards: turn
the counterweight clockwise .
6) Put the tone arm back onto the tone arm
support and secure it with the locking
lever (8) .
7) The counterweight is provided with a black
rotary ring with a scale . The red line on the
tone arm points to a value on this scale .
Without turning the counterweight, only
turn the ring to "0" (fig . 4) .
8) The scale indicates the stylus pressure in
grams . A stylus pressure of 2 g is required
for the supplied stylus system . For this pur-
pose, turn the counterweight (not only
the ring with the scale!) counter-clockwise
until the red line on the tone arm points
to "2" (fig . 5) .
For other stylus systems, adjust the
stylus pressure indicated in the correspond-
ing specifications .
4.2 Adjusting the antiskating facility
When playing a record, forces occur on the
stylus which are compensated by the an-
tiskating facility . For this purpose, adjust the
antiskating knob (6) from "0" to the value
which equals the stylus pressure, i . e . for the
supplied stylus system to "2": The arrow next
to the knob points to the corresponding value
on the knob .
4.3 Mounting the dust cover
Take the two hinges for the dust cover out
of the two polystyrene wrappings and attach
them to the dust cover . Place the dust cover
with the hinges on the turntable . It can be
removed at any time if it inter feres with the
operation (e . g . during disco operation) .
5 Connecting the Turntable
Prior to connecting or changing existing con-
nections switch off the turntable .
1) Connect the cable with the phono
plugs (18) – red for the right channel,
white for the left channel – to the corre-
sponding input jacks at the amplifier or
mixer:
a When connecting to input jacks for a
turntable with magnetic system set the