Technical Data; Noise Information; Declaration Of Conformity - Bosch GAS 35 L AFC Professional Originalbetriebsanleitung

OBJ_BUCH-1746-002.book Page 18 Tuesday, July 23, 2013 1:17 PM
18 | English

Technical Data

Wet/dry vacuum cleaner
Article number
3 601 JC3 ...
Rated voltage
Rated power input
Frequency
Container volume (gross)
Net volume (for fluids)
Dust bag contents
Max. vacuum*
– Vacuum cleaner hPa
– Turbine hPa
Max. flow rate*
– Vacuum cleaner
– Turbine
Max. vacuum capacity
Surface of flat-fold filter
Dust category
Weight according to
EPTA-Procedure 01/2003
Protection class
Degree of protection
Ø
* Measured with a 35 mm and 5 m long vacuum hose
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
max. power
Rated voltage
EU 220 –240 V
UK 110 V
UK/DK 240/230 V
CH 230 V
* Specification of the allowable load of the connected power tool (coun-
try-specific)

Noise Information

Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
1 609 92A 0D1 | (23.7.13)
Henk Becker
Executive Vice President
GAS 35 L AFC
Engineering
... 2.. ... 270
V 220 –240 110
W 1200 1000
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Hz 50/60 50/60
25.07.2013
l 35 35
l 19 19
Assembly
l 19 19
 Before any work on the vacuum cleaner itself, pull the
230 211
254 242
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 5 firmly from above into the
36 31
l/s
l/s 74 71
Mounting the Vacuum Hose (see figure B)
W 1380 1150
– Mount the vacuum hose 21 onto the hose connection
2
m 0,615 0,615
L L
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused through the friction
kg 12,2 12,2
of the dust, which the operator could experience in the form
/I /I
of static discharging (dependent on environmental influences
IP X4 IP X4
and physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory), when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories (see figure C)
min. power
The vacuum hose 21 is equipped with a clip system, with
output output
which the VAC accessories (tool sleeve 20, elbow 22) can be
connected.
2200 W 100 W
750 W 100 W
Mounting the Tool Sleeve
– Mount the tool sleeve 20 onto the vacuum hose 21 until
1800 W 100 W
1100 W 100 W
– To disassemble, press both snap-fasteners 31 inward and
Mounting Nozzles and Tubes
– Mount the elbow 22 onto the vacuum hose 21 until both
– Afterwards, mount the desired VAC accessory (floor noz-
– To disassemble, press both snap-fasteners 31 inward and
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures D1
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
mains plug.
retainers 30 intended for this purpose, until they engage.
piece 2 and turn it in clockwise direction to the stop.
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
pull the components apart.
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
pull the components apart.
D2)
–
Bosch Power Tools