Technical Data; Noise/Vibration Information - Bosch GAS 55 M AFC Professional Originalbetriebsanleitung

(33) Brush inserts
(34) Floor nozzle
(35) Suction tube
(36) Adapter for vacuum hose holder
(37) Snap fastener
(38) Control LED
(39) Filter cover
(40) Fill level sensors

Technical data

Wet/dry extractor
Article number
Rated power input
Frequency
Container volume (gross)
Net volume (liquid)
Dust bag volume
A)
Max. vacuum
– Dust extractor
– Turbine
A)
Max. volume flow rate
– Dust extractor
– Turbine
Max. suction power
Area of pleated filter
Dust class
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
Protection rating
A) Measured using a vacuum hose 3 m long and 35 mm in diameter
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Automatic start/stop
Rated voltage Maximum power Minimum power
230 V 2200 W
Permitted connected load of the connected power tool.
These values can differ for other country-specific models. Please take
note of the information on the socket of the dust extractor.

Noise/Vibration Information

Noise emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the dust ex-
tractor is 70 dB(A). Uncertainty K = 3 dB. The noise level
when working can exceed 80 dB(A).
Bosch Power Tools
Wear hearing protection
Total vibration values a
determined according to EN 60335-2-69: a
K = 1,5 m/s
Assembly
Pull the plug out of the socket before carrying out any
u
work on the dust extractor.
Fitting the holder for the vacuum hose (see
figure A)
– Slide the holder (4) for the vacuum hose firmly into the
GAS 55 M AFC
corresponding adapters (36) from above until they click
3 601 JC3 3..
into place.
W 1200
Fitting the vacuum hose (see figure B)
Hz 50–60
– Attach the vacuum hose (27) to the hose adapter (3) and
l 55
turn it clockwise as far as possible.
l 40
Note: The friction generated by the dust in the vacuum hose
l 27
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
hPa 230
state).
hPa 254
Bosch generally recommends using an anti-static vacuum
hose (accessory) to vacuum up fine dust and dry materials.
l/s 36
Fitting the vacuuming accessories (see figure C)
3
m /s 0.036
The vacuum hose (27) is equipped with a clip system which
l/s 74
can be used to connect vacuuming accessories (dust extrac-
3
m /s 0.074 tion adapter (25), curved nozzle (28)).
W 1380
Fitting the nozzles and tubes
2
m 0.615
– Push the curved nozzle (28) onto the vacuum hose (27)
until you hear both snap fasteners (37) on the vacuum
M
hose engage.
kg 16.2
– Then attach the required extraction accessory (floor
nozzle, crevice nozzle, suction tube, etc.) firmly to the
/ I
curved nozzle (28).
IPX4
– To remove the accessory, press the snap fasteners (37)
inwards and pull apart the components.
Fitting the dust extraction adapter
– Push the dust extraction adapter (25) onto the vacuum
hose (27) until you hear both snap fasteners (37) on the
vacuum hose engage.
– To remove the adapter, press the snap fasteners (37) in-
100 W
wards and pull apart the components.
Inserting/removing the disposal bag or dust bag
(dry extraction) (see figure D)
A disposal bag (29) or dust bag must be used for the dry ex-
traction of dust class M materials.
Insofar as materials with or without an exposure limit of
≥ 1 mg/m
be sucked straight into the container.
(triax vector sum) and uncertainty K
h
2
.
3
(dust class L materials) are extracted, these can
1 609 92A 6R5 | (02.09.2021)
English | 21
2
<2,5 m/s ,
h