Bosch GGS 16 PROFESSIONAL Bedienungsanleitung Seite 9

1 609 929 J62.book Seite 1 Mittwoch, 26. April 2006 9:36 09
Tool Specifications
Straight grinder
Article number
Rated power input [W]
Output power [W]
No-load speed [rpm]
Collet Ø, max. [mm]
Grinding tool Ø,
max. [mm]
Weight according to
EPTA-Procedure
01/2003 [kg]
Protection class
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
The values given are valid for nominal voltages [U] of 230/
240 V. For lower voltages and models for specific coun-
tries, these values can vary.
Product Features
The numbering of the product features refers to
the illustration of the machine on the graphics
page.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
1 Collet chuck
2 Clamping nut
3 Grinder spindle
4 Spindle collar
5 On/Off switch
Illustrated or described accessories are not included as
standard delivery.
Noise/Vibration Information
Measured values determined according to
EN 50 144.
Typically the A-weighted noise levels of the ma-
chine are: Sound pressure level: 86 dB (A);
sound power level: 99 dB (A).
Wear hearing protection!
The typically weighted acceleration is 4.0 m/s
Intended Use
The machine is intended for grinding and deburr-
ing of metal with corundum grinding tools.
9 • 1 609 929 J62 • TMS • 12.04.06
GGS 16
PROFESSIONAL
0 601 209 1..
900
480
Additionally, the general safety instructions either in
16 000
the enclosed booklet or those added in the centre
10
of these operating instructions must be observed.
SAVE THESE INSTRUCTIONS.
50
Safety warnings common for grinding:
3.0
/ II
2
.
English - 1
For Your Safety
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
This power tool is to be used as a grinder.
Read all safety warnings, instructions, il-
lustrations and specifications provided
with this power tool. Failure to follow all in-
structions listed below may result in electric
shock, fire and/or serious injury.
This power tool is not suitable for sanding
with sanding discs, working with wire
brushes, polishing and cut-off grinding. Us-
age of the power tool other than intended for can
cause dangerous situations and lead to injuries.
Do not use accessories which are not spe-
cifically designed and recommended by
the tool manufacturer. Just because the ac-
cessory can be attached to your power tool, it
does not assure safe operation.
The rated speed of the accessory must be
at least equal to the maximum speed
marked on the power tool. Accessories run-
ning faster than their rated speed can fly apart.
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbour holes that do not match the mount-
ing hardware of the power tool will run out of
balance, vibrate excessively and may cause
loss of control.
Do not use a damaged accessory. Before
each use inspect the accessory such as abra-
sive wheels for chips and cracks, backing
pads for cracks, tear or excess wear, wire
brushes for loose or cracked wires. If the
power tool or accessory is dropped, inspect
for damage or install an undamaged acces-
sory. After inspecting and installing an acces-
sory, position yourself and bystanders away
from the plane of the rotating accessory and
run the power tool at maximum no-load
speed for one minute. Damaged accessories
will normally break apart during this test time.