Operation Mode Selection - Sparky BPR 240PE Originalbetriebsanleitung

WARNING: Reversing can be per-
formed only when the spindle is not rotating!
Otherwise this might cause damage to the
motor.

OPERATION MODE SELECTION

Switching between the operation modes shall be
performed only when the machine is turned off.
Press the release button 6 and turn the mode
selector switch 11 to the necessary position.
▪ Drilling (Fig.3) - drilling in metal, wood, plas-
tics, etc.
▪ Hammer drilling (Fig.4) - hammer drilling in
concrete, stone, etc..
▪ Hammer mode (Fig.5) - chiselling grooves
and demolishing in concrete, masonry, etc.
▪ Adjusting the chisel (Fig.6) - to avoid opera-
tor's fatigue, insert and fix the chisel in the
necessary position.
INSERTING AND REMOVING QUICK
CHANGE CHUCK (BPR 240PQE,
BPR 260PQE, BPR 280PQCE)
To insert SDS plus quick change chuck 13 or
quick change chuck set 14, place it in the open-
ing of spindle 17 and while pressing its front end
rotate releasing ring 15 until an audible "click" is
heard. (Fig.11)
To remove SDS plus quick change chuck 13 or
quick change chuck set 14 from the machine,
pull out releasing ring 15 in the direction shown
on fig. 12 and take the chuck out.
INSERTING AND fASTENING SDS
PLUS BITS
Clean and grease the shank of the accessory,
before placing it into the socket! (Fig.7)
Insert the bit into the socket. Ensure that the
socket grooves correspond to the bit shank
channels, and then press the bit inward until an
audible "click" is heard. (Fig. 8)
To remove the bit, pull the sleeve 3 backward,
and then take the bit out. (Fig.9)
WARNING: Never use bits with diam-
eter exceeding the indicated to avoid over-
loading the power tool.
8
EN
Reversing can be per-
BPR 220PЕ ● BPR 240PЕ ● BPR 240PQЕ ● BPR 260PЕ ● BPR 260PQЕ ●
INSERTING AND fASTENING DRILL
BITS WITH STRAIGHT SHANK INTO
THE CHUCK (BPR 220PE, BPR 240PE,
BPR 260PE, BPR 280PCE)
Place the mode selection switch 11 in position
«Drilling» (Fig.3). Insert the chuck 12 into the
SDS plus socket 4 as described above. In this
configuration the rotary hammer can operate in
drilling mode.
for keyed chuck
By turning the collar of chuck 12 clockwise or
anti-clockwise the jaws move to a position en-
suring inserting the drill bit shank. Rotate the
collar of the chuck clockwise to tighten the drill
bit shank. Fix the drill bit finally into the chuck
by means of the special chuck key, tightening
equally in all three bores.
for keyless chuck
Grip the securing ring 16 and rotate the front
collar until the chuck is opened sufficiently for
the tool to be inserted, and then tighten the front
collar. An audible "click" indicates that the chuck
has locked.
ADJUSTING THE CHISEL POSITION
Insert the chisel into the socket as it is described
in section "Inserting SDS-Plus bits".
Turn the operating mode switch 11 in position
«Adjusting the chisel» (Fig.6).
Rotate the tool by hand to the desired position
(Fig.10).
Turn the operating mode switch 5 to position
«Hammer» (Fig.5), and then turn the tool slightly
by hand leftwise and rightwise until it is locked.
Longer operation life of the rotary hammer and
higher efficiency can be achieved only with well
sharpened tools for demoliting and chiselling.
SCREWING / UNSCREWING BOLTS,
SCREWS AND NUTS
Following the above-described procedure, tight-
en the corresponding accessory into chuck 12
or 14. Set mode selector switch 11 to position
«Drilling» (Fig.3). Select the necessary rotation
direction by lever 7. These operations must be
performed only at low speed.
WARNING: In case of driving long
bolts and screws there is a danger of slipping
the rotary hammer!
BPR 280PCE ● BPR 280PQCE