Bosch PMF 350 CES Betriebshandbuch Seite 20

OBJ_BUCH-2652-001.book Page 20 Tuesday, October 6, 2015 2:04 PM
20 | English
Accessory
TC plunge cut saw
blade, metal
BIM plunge cut saw
blade, wood and
metal
HCS plunge cut saw
blade, wood
Mounting/Replacing the Application Tool/
Accessory (AutoClic) (see figures A and B)
If required, remove an already mounted application tool/
accessory.
To do so, open the AutoClic lever 1 all the way. The applica-
tion tool/accessory will be ejected.
Place the application tool/accessory on a flat surface. Press
the power tool onto the application tool/accessory at the re-
quired angle until it can be heard to engage (see illustration on
the graphics page; labelling on the application tool/accessory
can be read from above).
 Check the tight seating of the application tool/acces-
sory. Incorrect or not securely fastened application
tools/accessories can come loose during operation and
pose a hazard.
Mounting and Adjusting the Depth Stop
The depth stop 12 can be used when working with segment
saw blades.
If required, remove an already mounted application tool/
accessory.
Slide the depth stop 12 over and beyond the tool holder 7 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 12 from the tool holder 7 in
the direction of the application tool until you can rotate it
1 609 92A 1G5 | (6.10.15)
Material Application
Stainless steel (Inox), Fast, deep plunge cuts in severely abrasive materials or
Screws and nails, metal;
Epoxy resin, example: fast cutting of kitchen front covers, easy cutting
Glass fibre reinforced through hardened screws, nails and stainless steel
plastics,
Fibreglass,
Plasterboard,
Porous concrete
Wood, Fast, deep plunge cuts in wood, abrasive wooden materials
Abrasive wooden mate- and plastics;
rials, example: fast cutting of non-ferrous metal pipes and pro-
Plastics, files with smaller dimensions, easy cutting of non-hardened
Hardened nails and screws, nails, screws and steel profiles with smaller dimensions
Non-ferrous metal pipes
Softwood, Fast, deep separating and plunge cuts; also for sawing
Dowels, close to edges in corners and hard to reach areas;
Tenons, example: deep plunge cut in softwood for installing a venti-
Furniture components lation grid
freely. Rotate the depth stop 12 so that the desired cutting
depth is above the section of the saw blade, which will be
used to saw. Slide the depth stop 12 once again to the stop
onto the gear head of the application tool.
For all other cutting depths and when working with other ap-
plication tools, remove the depth stop 12. For this, remove
the application tool and pull the depth stop from the gear head.
Mounting the Auxiliary Handle
The vibration-damped auxiliary handle enables the tool to be
used safely and more comfortably.
Screw the auxiliary handle 6 on the right or left of the machine
head depending on the working method.
 Do not continue to use the power tool when the auxil-
iary handle is damaged. Do not make any changes or
modifications to the auxiliary handle.
Mounting/Replacing a Sanding Sheet on the
Sanding Plate
The sanding plate 10 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 11, free the Velcro back-
ing of the sanding plate 10 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 11 flush alongside one edge of the
sanding plate 10, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 11, grasp it at one of the tips and
pull it off from the sanding plate 10.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Bosch Power Tools