Warranty And Liability; Declaration Of Conformity; Environmental Protection, Disposal - Fein ASCT5-40 Originalbetriebsanleitung

OBJ_BUCH-0000000006-001.book Page 17 Wednesday, June 23, 2010 8:08 AM
Use only intact original FEIN batteries that are intended
for your power tool. When working with and charging
incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Operating instructions.
Adjust the Rotation selector switch only when the
machine is at a complete stop.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at no-
load speed.
ASCT5-40/ASCT5-40M: The screwdriving applications are
to be carried out with mounted depth stop.
ASCT5-40M/ASCT5-40UM: The collated cartridge may
only be operated in "clockwise-rotation direction" posi-
tion.
Setting the torque (ASCT5-40U/ASCT5-40UM) (see
page 7)
The factory setting is for the small to mid-size screw
range.
The tightening torque also depends on the force with
which the power tool is pressed against the screw.
Handling the battery.
Charge batteries only in ambient temperatures between
0 °C and 40 °C. At the beginning of the charging proce-
dure, the battery temperature may not exceed 45 °C.
The battery capacity indication displays the true value
only when the motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
To counteract against service-life reduction and maintain
the optimal capacity of your battery:
– Charge new batteries before using
– Do not continue to press the power tool's On/Off
switch when the automatic motor shut-off responds
– Charge batteries fully before storing them.
Meaning of the LED indicator on the battery:
LED indicator Meaning
Red flashing light The battery is defective
Continuous red light Charge condition ≤ 10%
1 – 4 green LED Percentage of charge condition
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air.
If required, you can change the following parts your-
self:application tools, depth stop, battery, hand strap, belt
clip, magazine

Warranty and liability.

The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate
the terminals with tape as a protective measure against
short-circuiting.
en
17