Phottix Mitros+ Benutzerhandbuch Seite 12

the camera to control and trigger Mitros+ flashes in OP Rx (Slave), or other com-
patible flashes in Slave mode.
OP Tx (Master) Mode:
1. Pressing button will allow changes to be made to the flash firing,
transmission channel and ratio mode and ratio.
2. Press the button to turn the flash firing on or off.
3. With transmission channels highlighted, press the
buttons to change the channel from 1-4.
4. With the ratio mode highlighted, press the
to change the wireless ratio mode. (see below).
5. With the ratio highlighted, press the
change the wireless ratio. (see below).
6. Press the button to confirm and exit the screen.
Master with Flash mode TTL:
when a photo is taken.
Master without Flash mode TTL:
not fire when a photo is taken. The flash will emit a short burst of light to
communicate with Slave flashes but this light will not be part of the exposure.
To set OP Rx (Slave) Mode:
1. Press the button to set TTL or M for the Slave.
2. Pressing button will allow changes to be made to the flash's chan-
nel and group.
3. With transmission channels highlighted, press the
buttons to change the channel from 1-4.
4. With group highlighted, Press the
the group the flash is assigned to (A, B).
5. Press the button to enter the power adjustment screen. The power
level will flash and be highlighted.
6. Press the or
7. Press the button to confirm and exit the screen.
8. When OP Rx (Slave) flashes are ready to shoot the AF Assist light on the
front of the flash will blink once every 1 second.
Please note:
- Make sure the OP Tx (Master) and OP Rx (Slave) flashes are set to the same
transmission channel (1-4).
- Do not place any obstacles between the Master unit and Slave unit(s). Ob-
stacles can block signal transmissions.
- When using wireless bounce flash, please ensure the Slave flash Wireless
Signal Receiver Area faces toward the Master flash.
- When using only one flash set Wireless Mode to "Off".
12
and
and
and buttons to
The Master flash on the camera will fire
The Master flash on the camera will
and
and buttons to change
buttons to adjust the flash power.
En
Transmission Channels
The Phottix Mitros+ OP Tx/Rx Wireless system has four transmission channels: 1,
2, 3 and 4. Signals from the OP Tx (Master) flash are sent to OP Rx (Slave) flashes
on these channels. If Master and Slave flashes are set to different channels the
Slave flashes will not fire.
Using OP Tx/Rx Wireless Triggering
With a flash in OP Tx (Master) mode on the camera and remote flashes in OP Rx
Slave mode, pressing the shutter button will fire the OP Tx (Master) flash (if set to
fire the flash) and flashes set to OP Rx (Slave) mode within the range of the OP Tx
buttons
(Master) flash. The camera and flash will meter the scene and fire flashes in TTL
mode to properly expose the scene.
Ratio Modes
Slave flashes can be controlled by the Master flash in two different Ratio Modes:
M: A
All Slave flashes no matter in groups A or B are regarded as the same
group. There are only two groups: Master and Slave group.
M: A: B
There are three groups: Master, Slave group A and Slave group B.
Phottix Mitros+ TTL transceiver flash for Sony has two TTL modes: TTL and TTL
Auto mode. Please see above and below for more details.
TTL Modes:
M: A
Master flash will not fire. All Slave flashes (no matter in groups A or B)
will fire as metered and/or with the same flash power.
M: A: B
Master flash will not fire. Only Slave group A will fire. Slave group B
will not fire.
TTL Modes:
M: A
Flash ratio can be set for Master and Slave groups (A and B). Master and
Slave groups will fire at the selected flash ratio.
M: A: B
Flash ratio can be set for Master, Slave groups A and B. Three groups
will fire at the selected flash ratio.
Manual Modes
M: A
Master flash will fire at the selected manual power level. Slave groups
(A and B as the same group) will fire at the TTL metering result and the select-
ed flash ratio.
M: A: B
Master flash will fire at the selected manual power level. Slave group
A and Slave group B will fire at the TTL metering result and the selected flash
ratio.
Please note:
1. If it is set to M:A ratio mode, any one of the groups can be turned off by
setting the flash ratio to "-"(OFF).
2. If it is set to M:A:B ratio mode, any two of the groups can be turned off by
setting their flash ratio to "-"(OFF).
INSTRUCTION MANUAL