Phottix Mitros+ Benutzerhandbuch Seite 11

Please note:
The flash on camera (L) is not part of the ratio calculation. Power for the local
flash is controlled independently.
Adjusting Flash Head Zoom in Odin Tx Mode
1. Pressing the button will open the Zoom Adjustment Menu.
2. The and
3. The and Arrow buttons will adjust from Azoom (automatic
zoom that changes dynamically as a zoom lens is changed) and Mzoom 24,
28, 35, 50, 70, and 105mm.
4. Pressing the button will exit Zoom Adjustment Mode.
Adjusting Transmission Channels
1. From the Odin Tx or Ratio Menu, press the
Transmission Channel selection.
2. Press the and
3. Press the button to lock in the channel.
Using High Speed Sync (HSS) and Second Curtain Sync (SCS) in
Odin Tx Mode
High Speed Sync (HSS)
1. Pressing the button will cycle between HSS on / HSS off.
2. HSS will allow faster shutter speeds to be used. Shutter speeds up to 1/8000
sec. can be achieved with compatible cameras.
Note:
At high shutter speeds the power of flashes is greatly reduced.
Second Curtain Sync(SCS)
1. SCS cannot be set on the Mitros+ flash directly.
2. Set the camera flash mode to "SCS". See your camera user manual for more
details.
3. SCS will fire the flash at the end of an exposure, not at the beginning. This
can be combined with longer exposures for creative effects.
Odin Rx (Receiver) Mode
Odin Rx Mode screen
When the Odin Rx Wireless mode is selected the Phottix Mitros+ Flash will trig-
ger using a built-in Odin-compatible receiver. While in Odin Rx Mode the Mi-
tros+ can be controlled and triggered from another Mitros+ Flash in Odin Tx
Mode or an Odin TCU.
11
Arrow button will cycle though groups L, A, B, C.
button to access the
buttons to cycle through Channels 1-4.
INSTRUCTION MANUAL
En
Changing Channels and Groups
1. Press the button to access the Channel and Group selection.
2. Use the and
3. Use the and
or group assignment (A-C).
4. Press the button to exit Channel and Group editing mode.
Please note:
The effect of EV adjustment is cumulative. If EV adjustment is set on the Odin
Rx screen and on an Odin TCU or Mitros+ in Odin Tx mode, and/or in TTL Pref
in the Custom Functions menu, all of these settings will be used to calculate
the final EV.
Strato II Rx Mode
Strato II Rx Mode screen
When the Strato II Rx Mode is selected the Mitros+ will be triggered by Phottix
Strato II Multi Transmitters, a Phottix Odin TCU or Phottix Mitros+ in Odin Tx
mode.
1. Press the button to access the Channel and Group selection.
2. Use the and
3. Use the and
or group assignment (A-C).
4. Press the button to adjust the Manual Power level of the Mitros+
(from 1/1 to 1/128 in 1/3 stops). Press the
Power Adjustment Mode.
5. Press the Button to edit the flash head zoom. Pressing the
and buttons will cycle between AZoom and MZoom settings. Press
the button to return to the main menu.
Please note:
In Strato II Rx (Receiver) Mode there are no wireless TTL functions such as HSS
or SCS, or wireless power/zoom control. Power and zoom levels must be set
manually on the Mitros+ Flash while in Strato II Rx Mode.
OP Tx (Master) and OP Rx (Slave) Wireless Modes
OP Tx (Master) and OP Rx (Slave) modes use Sony wireless control and triggering
system. A Mitros+ flash set to OP Tx (Master) is needed on the camera to con-
trol remote (Slave) flashes set to OP Rx (Slave). The same transmission channel
needs to be set on both Master and Slave flashes. Groups need to be set for
Slave flashes, Group Ratio functions need to be set for Master flashes. A Mitros+
set to OP Tx (Master) or other compatible flash in Master mode can be used on
buttons to select Channel or Group.
buttons to adjust the reception channel (1-4)
buttons to select Channel or Group.
buttons to adjust the reception channel (1-4)
button again to exit Manual