Safety Instructions It is absolutely essential that you read these safety instructions carefully before connecting and using this K+H product. Your safety depends on it. Failure to follow these instructions voids the warranty. To ensure safe operation for years to come, keep these instructions in a safe place for future reference. K+H has manufactured this product in accordance with IEC 92 (SEC) 39 standards, then tested and delivered it in safe operating condition.
Two 8-channel devices may be stacked up to populate all the available 16 channels on a K8 cable. For example, 16 analogue inputs are obtained by stacking quantity (2) K8-AI8 devices. Stacking two devices is accomplished using a standard Ethernet crossover cable to connect the K8 Out 2 of the first device to the K8 Out 1 of the second device.
AI8 only has 8 inputs? Up to two input units such as the K8-AI8 (analogue line input) may be used to place audio onto the K8 bus. One of the two input units must be connected to the system via a standard category 5 crossover cable.
How far can you run a K8 cable? How far can you run a K8 cable? How far can you run a K8 cable? How far can you run a K8 cable? One K8 distribution leg can be run a total length of 200 meters no matter how many devices are connected along the way.
Cal and DIP switch rear panel level trim adjustments. Overview The K8-AI8 is a K8 input device allowing 8 analogue audio channels to be placed onto the K8 bus. Stacking Input Devices Two AI8 devices may be stacked to populate all 16 available audio channels. Alternately, the AI8 may be combined with any other 8 channel input device for a total of 16 channels.
PIN 1 Phantom Ground PIN 2 Phantom Power PIN 3 Data A (+) PIN 4 Data B (-) PIN 5 Signal Ground DB9 Female Control Connector PIN 6-9 Not Used The phantom power is used to drive K8 accessories designed to attach to the local control connector, such as a local volume control wall plate.
K8-AI8 Technical Specifications Electrical Frequency Response Frequency Response Frequency Response Frequency Response 20 Hz – 22 kHz >100dB(A) Signal to Noise Ratio Signal to Noise Ratio Signal to Noise Ratio Signal to Noise Ratio Input Input Input Input Balanced analogue audio, XLR-1/4” female combo connector x 8...
Routing Capabilities As shipped from the factory, the K8-AO8 will place audio channels 1-8 on outputs 1-8. The K8 bus contains 16 audio channels, in two groups of 8. The K8 terminal control protocol is capable of configuring the K8-AO8 to select either the group of channels numbered 1-8 or the group of channels numbered 9-16 for output.
Front Panel LEDs Each input channel has 3 front panel LEDs to show channel level. The green LED illuminates at signal present 32 dB below digital full scale. The yellow LED illuminates at nominal level 12 dB below digital full scale.
K8-AO8 Technical Specifications Electrical Frequency Response Frequency Response Frequency Response Frequency Response 20 Hz – 22 kHz Signal to Noise Ratio Signal to Noise Ratio >100dB(A) Signal to Noise Ratio Signal to Noise Ratio Input Input Input Input K8 digital audio bus, RJ-45 Output Output 8 x analogue audio out, XLR male connectors...
Overview The K8-AO2 is a K8 output device for receiving 2 audio channels from the K8 bus and decoding them into 2 analogue outputs. Routing Capabilities As shipped from the factory, the K8-AO2 will place audio channels 1,2 on outputs 1,2. The two outputs of the AO2 device can select any stereo pair from the K8 bus.
The output levels of an AO2 may be trimmed down to any lower value by using the K8 terminal control protocol. Front Panel LEDs Each input channel has 3 front panel LEDs to show channel level. The green LED illuminates at signal present 32 dB below digital full scale.
K8-AO2 Technical Specifications Electrical Frequency Respo Frequency Response Frequency Respo Frequency Respo 20 Hz – 22 kHz Signal to Noise Ratio Signal to Noise Ratio >100dB(A) Signal to Noise Ratio Signal to Noise Ratio Input Input Input Input K8 digital audio bus, RJ-45 Output Output 2 x analogue audio out, XLR male connectors , RCA cinch connectors and...
Stacking Input Devices It is also possible to turn off 8 channels of a 16 channel device, such as the K8-ESB, and combine it with 8 channels of another audio input type, such as the K8-AI8 analog inputs. The 4 CONFIG DIP switch on the K8-ESB is used to turn off transmission of channels 9-16, making it function like any other 8 channel K8 input device.
Termination Setting The first 3 configuration DIP switches must be set to “on” when the ESB is the last device in the K8 chain. K8 link port connected: Termination Off K8 link port not connected: Termination On Control and Monitoring All devices on the K8 bus may be controlled and monitored through a single RS-485 connection to the ESB device.
K8-ESB Technical Specifications Electrical Frequency Response Frequency Response 20 Hz – 22 kHz Frequency Response Frequency Response Input Input Input Input EtherSound ES100, IN and OUT Output Output Two K8 bus outputs, each drives 200 meters Output Output Control Control Control Control RS-485, DB-9 female connector, open published protocol...
Seite 24
Notes Page 24 K8 Rackmount Family User Manual...
Seite 25
Digital Audio Distribution System Manuel Utilisateur K8-AI8 K8-AO2 K8-AO8 K8-ESB...
Instructions de sécurité Il est absolument essentiel de lire avec attention ces instructions de sécurité avant de brancher et d’utiliser ce produit K+H. Votre sécurité en dépend. La garantie du produit est annulée si vous ne suivez pas ces instructions. Afin d’assurer un fonctionnement sans problème pendant des années, conservez ce manuel utilisateur en lieu sûr, afin de pouvoir vous y référer facilement à...
Seite 27
Contrôle et surveillance à distance du système..................35 Réglage des niveaux d’entrée ........................35 LED en face avant ............................35 Accessoires compatibles..........................35 Caractéristiques techniques du module K8-AI8 ..................36 Caractéristiques électriques........................... 36 Caractéristiques mécaniques......................... 36 SECTION SPÉCIFIQUE AU MODULE K8-AO8 Description du panneau arrière ........................
Seite 28
SECTION SPÉCIFIQUE AU MODULE K8-AO2 Description du panneau arrière ........................41 Description de la face avant ......................... 41 Présentation générale ........................... 42 Possibilités d’assignation (routing)......................42 Chaînage de périphériques de sortie......................42 Réglage des terminaisons ..........................42 Contrôle et surveillance à distance du système..................42 Réglage des niveaux de sortie........................
Pour chaîner (‘stack’) deux modules, il suffit de relier le bus de sortie K8 Out 2 du premier module à la sortie K8 Out 1 du second. Il ne reste alors plus qu’à relier la sortie K8 Out 1 du premier module au bus K8. Module d'entrée analogique K8-AI8 K8 Out 1...
trouvent en position On. Si l’un des ports K8 d’un module n’est pas connecté, les 4 sélecteurs sont en position Off. Le protocole de contrôle des terminaux K8 est capable de vérifier à distance les positions des sélecteurs de terminaison. Les modules d’entrée servent à...
Seite 31
EIA-568B. Dans le système K8, le câble Cat5 croisé sert à « chaîner » (stack en anglais) sur un même câble deux modules d’entrée, tels que le K8-AI8. Tous les autres câbles Cat5 utilisés doivent être « droits ».
Déclarations du fabricant Déclaration de conformité pour la CEE Ces appareils sont conformes aux exigences essentielles et aux autres dispositions pertinentes de les Directives 89/336/EC et 73/23/EC. Vous trouvez cette déclaration dans la internet sous www.klein- hummel.com. Avant d'utiliser l'appareil, veuillez observer les dispositions légales en vigueur dans votre pays.
SECTION SPÉCIFIQUE AU MODULE K8-AI8 Description du panneau arrière RS 485 AC IN 100-240V AC, 50-60Hz +4dBu K8 OUT -10dBV TERM Overload Wink INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 INPUT 7 INPUT 8 Max. Power Consumption 15Watts Made in Germany Panneau arrière du K8...
Cal et les sélecteurs DIP de sensibilité situés sur le panneau arrière Présentation générale Le K8-AI8 est un module d’entrée qui se connecte sur un bus K8. Il permet d’y injecter les signaux numériques correspondant à 8 entrées audio analogiques. Chaînage des modules d’entrée Vous pouvez «...
Un seul port de sortie vers le bus K8 est connecté : Sélecteur de terminaison sur On Contrôle et surveillance à distance du système Vous pouvez contrôler et surveiller à distance les modules reliés au bus K8, via une seule connexion, au protocole RS-485, ramenée au module AI8.
Caractéristiques techniques du module K8-AI8 Caractéristiques électriques Réponse en fréquen Réponse en fréquence ce ce ce Réponse en fréquen Réponse en fréquen 20 Hz – 22 kHz > 100 dB(A) Rapport Signal/Bruit Rapport Signal/Bruit Rapport Signal/Bruit Rapport Signal/Bruit Entrées audio Entrées audio...
SECTION SPÉCIFIQUE AU MODULE K8-AO8 Description du panneau arrière RS 485 AC IN 100-240V AC, 50-60Hz OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8 K8 INPUT K8 LINK TERM Sync Wink Max. Power Consumption 20Watts Made in Germany Panneau arrière du K8 Panneau arrière du K8...
Possibilités d’assignation (routing) À sa sortie d’usine, le module K8-AO8 envoie les canaux audio 1 à 8 sur les sorties 1 à 8. Le bus K8 transporte un maximum de 16 canaux audio, répartis en deux groupes de 8. Le protocole de contrôle de terminal K8 permet de configurer le module K8-AO8 pour sélectionner, en sortie, soit le groupe de canaux numérotés de 1 à...
de sortie analogiques : un signal envoyé à un certain niveau dans un module AI8 ressort au même niveau dans un module de sortie AO8. Le niveau de sortie d’un module AO8 peut être « trimmé » à n’importe quelle valeur inférieure, en utilisant le protocole de contrôle de terminal K8.
Caractéristiques techniques du module K8-AO8 Caractéristiques électriques Répons Réponse en fréquence Répons Répons e en fréquence e en fréquence e en fréquence 20 Hz – 22 kHz Rapport Signal/Bruit Rapport Signal/Bruit > 100 dB(A) Rapport Signal/Bruit Rapport Signal/Bruit Connecteur Input Connecteur Input Connecteur Input Connecteur Input...
SECTION SPÉCIFIQUE AU MODULE K8-AO2 Description du panneau arrière Max. Power Consumption 10Watts RS 485 OUTPUT 1 OUTPUT 2 K8 INPUT K8 LINK OUT 2 TERM OUT 2 AC IN: 100-240V AC, 50-60Hz Made in Germany Panneau arrière du K8 Panneau arrière du K8 Panneau arrière du K8 Panneau arrière du K8- - - - AO2...
Présentation générale Le K8-AO2 est un module de sortie qui se connecte sur un bus K8. Il permet d’y récupérer les signaux numériques correspondant à 2 canaux audio, et les convertit sur 2 sorties analogiques. Possibilités d’assignation (routing) À sa sortie d’usine, le module K8-AO2 envoie les canaux audio 1 et 2 sur les sorties 1 et 2. Vous pouvez assigner aux deux sorties du module AO2 n’importe quelle paire stéréo du bus K8.
existe un gain unitaire entre module d’entrée et module de sortie analogiques : un signal envoyé à un certain niveau dans un module AI8 ressort au même niveau dans un module de sortie AO2. Les connecteurs RCA sont réglés en usine pour un niveau de sortie nominal de -10 dBV. Vous pouvez “trimmer”...
Caractéristiques techniques du module K8-AO2 Caractéristiques électriques Réponse en fréquence Réponse en fréquence Réponse en fréquence Réponse en fréquence 20 Hz – 22 kHz Rapport Signal/Bruit Rapport Signal/Bruit > 100 dB(A) Rapport Signal/Bruit Rapport Signal/Bruit Connecteur Input Connecteur Input Connecteur Input Connecteur Input Bus audionumérique K8, sur connecteur RJ-45 Connecteur Link...
SECTION SPÉCIFIQUE AU MODULE K8-ESB Description du panneau arrière Max. Power Consumption 20Watts RS 485 EtherSound Network K8 OUT CONFIG Link Activity AC IN: 100-240V AC, 50-60Hz Made in Germany Panneau arrière du K8 Panneau arrière du K8- - - - ESB Panneau arrière du Panneau arrière du RS 485...
Description de la face avant K8 DIGITAL AUDIO DISTRIBUTION ETHERSOUND BREAKOUT K8- ESB POWER Face avant du module K8 Face avant du module K8- - - - ESB Face avant du module K8 Face avant du module K8 LED Power LED Power LED Power LED Power...
Module d 'entrée K 8-ESB Module d'entrée analogique K 8-AI8 Sortie vers Out to CONFIG K8 Out 1 TERM K8 Out 1 distribution Distribution K8 Out 2 K8 Out 2 Canaux d'entrée 1 à 8 Canaux d'entrée 1 à 8 Câble Cat5 croisé...
Caractéristiques techniques du module K8-ESB Caractéristiques électriques Réponse en fréquence Réponse en fréquence 20 Hz – 22 kHz Réponse en fréquence Réponse en fréquence Connecteurs d’entrée Connecteurs d’entrée Connecteurs d’entrée Connecteurs d’entrée EtherSound ES100, IN et OUT Connecteurs de sortie Connecteurs de sortie 2 sorties de bus K8, longueur maximale de liaison 200 mètres chacun Connecteurs de sortie...
Seite 49
Notes Manuel Utilisateur Famille Produits K8 Page...
Seite 50
Notes Page 50 Manuel Utilisateur Famille Produits K8...
Seite 51
Digital Audio Distribution System Bedienungsanleitung K8-AI8 K8-AO2 K8-AO8 K8-ESB...
Sicherheitshinweise Das Gerät wurde von K+H gemäß IEC 92 (sec) 39 gebaut und hat unser Werk in sicherheitstechnisch einwandfreiem Zustand verlassen. Um diesen Zustand zu erhalten und einen gefahrlosen Betrieb sicherzustellen, muß der Anwender die Hinweise und Warnvermerke beachten, die in der Bedienungsanleitung enthalten sind.
Seite 53
Häufig gestellte Fragen (FAQ) ........................56 Herstellererklärungen CE Konformitätserklärung..........................57 Beschreibung des K8-AI8 Rückseitenbeschreibung ..........................58 Beschreibung der K8-AI8 Bedienfront ......................59 Übersicht ................................59 Kaskadieren von Eingangsgeräten......................59 Einstellen der Terminierung.......................... 59 Steuerung und Fernüberwachung....................... 59 Einstellen der Eingangsempfindlichkeit..................... 60 LEDs auf der Vorderseite ..........................
Seite 54
Beschreibung K8-AO2 Beschreibung Rückseite ..........................66 Beschreibung des Bedienteils........................66 Überblick ................................67 Routing Möglichkeiten ..........................67 Kaskadieren von Ausgangsgeräten ......................67 Einstellen der Terminierung.......................... 67 Steuerung und Fernüberwachung....................... 67 Ausgangspegel Einstellung .......................... 67 LEDs auf der Vorderseite ..........................67 Kompatibles Zubehör.............................
Zwei K8 Komponenten mit je 8 Kanälen können einfach zusammengeschaltet werden, um die K8 Kapazität von 16 Kanälen auf einem CAT5 Kabel voll auszunutzen. 16 analoge Eingangskanäle können zum Beispiel durch den Einsatz von zwei K8-AI8 Einheiten im K8 Format übertragen werden. Die Zusammenschaltung wird mittels Einsatz eines handelsüblichen Ethernet Crossover Kabels vorgenommen.
Eingangskomponenten dienen zur Kodierung von Audiosignalen in das K8 Format, Ausgangskomponenten dekodieren hingegen das K8 Format in das gewünschte Ausgangsformat. Ausgangskomponenten können hintereinander geschaltet werden, bis die maximale Leitungslänge von 200 Metern erreicht ist. Ausgangskomponenten werden passiv verschaltet und refreshen nicht das K8 Signal.
Es könne zwei Eingangeinheiten, wie z. B. K8-AI8 kombiniert werden, um Audiokanäle in einen K8 Bus einzuspeisen. Dabei muss eine der beiden Einheiten mit einem handelsüblichen Cat 5 Kreuzkabel an den Bus angeschlossen werden. Wie erstelle ich ein Cat5 Crossover Kabel?
Nicht benutzt Term K8 Eingangskanäle 9-16 Einstellen der Terminierung Alle vier TERM Schalter müssen auf ON stehen, wenn ein K8-AI8 das erste Gerät einer Kette ist. Beide K8 Outs angeschlossen Terminierung Aus Nur einer der K8 Outs angeschlossen: Terminierung Ein Steuerung und Fernüberwachung...
über diese Verbindung zu betreiben. Die Phantomspeisung ist im Auslieferzustand deaktiviert Einstellen der Eingangsempfindlichkeit Der K8-AI8 wird ausgeliefert um mit nominellen +4dBu betrieben werden zu können. Zum Anschluss von Geräten mit unsymmetrischen Cinch- oder Klinkensteckverbindern wie beispielsweise CD oder MP3 Player, kann mit den DIP Schaltern die Empfindlichkeit auf –10dBV herabgesetzt werden.
Terminierungsschalter Digital Audio Format Digital Audio Format Digital Audio Format Digital Audio Format 48 kHz Sampling Frequenz, 24 bit, proprietär Latenz Latenz 0,5ms von K8-AI8 zu K8-AO8 Latenz Latenz Stomversorgung Stomversorgung Stomversorgung Stomversorgung 100 – 240 Volt, 50-60Hz 15 Watt...
Ausgangspegel Einstellung Der K8-AO8 wird werkseitig so ausgeliefert, dass ein Signal mit einer nominellen Empfindlichkeit von +4dBu verarbeitet wird. D. h. ein Signal, das an einem K8-AI8 mit +4dBu eingespeist wird, wird an einem K8-AO8 ebenfalls mit +4dBu wieder ausgegeben.
Kompatibles Zubehör K8- - - - 485 USB zu RS-485 Adapterkabel zum Anschluss eines PCs zur Konfiguration. K8- - - - *** Eine stetig wachsende Vielzahl an Ein- und Ausgangsgeräten für das K8 System. Seite 64 K8 Bedienungsanleitung...
Terminierungsschalter Digital Audio Format Digital Audio Format 48 kHz Sampling Frequenz, 24 bit, proprietär Digital Audio Format Digital Audio Format Latenz Latenz 0,5ms von K8-AI8 zu K8-AO8 Latenz Latenz Stromversorgung Stromversorgung Stromversorgung Stromversorgung 100 – 240 Volt, 50-60Hz 15 Watt...
Ausgangspegel Einstellung Der K8-AO2 wird werkseitig so ausgeliefert, dass ein Signal mit einer nominellen Empfindlichkeit von +4dBu verarbeitet wird. D. h. ein Signal, das an einem K8-AI8 mit +4dBu eingespeist wird, wird an einem K8-AO8 ebenfalls mit +4dBu wieder ausgegeben.
Die Pegelanzeige zeigt das Wandlerausgangssignal an, d. h. ggf. nach der Beeinflussung mit der PC Schnittstelle. Kompatibles Zubehör K8- - - - 485 USB zu RS-485 Adapterkabel zum Anschluss eines PCs zur Konfiguration. K8- - - - *** Eine stetig wachsende Vielzahl an Ein- und Ausgangsgeräten für das K8 System. K8- - - - RMK Rackeinbauwanne zur Aufnahme von zwei Halb-19“-Geräten K8- - - - FMK...
Terminierungsschalter Digital Audio Format Digital Audio Format Digital Audio Format Digital Audio Format 48 kHz Sampling Frequenz, 24 bit, proprietär Latenz Latenz 0,5ms von K8-AI8 zu K8-AO2 Latenz Latenz Stromversorgung Stromversorgung Stromversorgung Stromversorgung 100 – 240 Volt, 50-60Hz 15 Watt...
Wenn man mit dem Konfigurationsschalter auf der Rückseite den 8-kanal Betrieb einstellt, kann ein K8- ESB mit einem anderen K8 Geräte (z. B. K8-AI8) zu einem neuen 16 Kanalsystem kaskasiert werden. Die Zusammenschaltung wird mittels Einsatz eines handelsüblichen Ethernet Crossover Kabels vorgenommen.
Steuerung und Fernüberwachung Alle Geräte eines K8 Bus Segments können von einem einzigen Port des K8-ESB aus eingestellt und überwacht werden. Das Steuerprotokoll ist unter www.klein-hummel.com frei verfügbar. Die Belegung des RS-485 Anschlusses ist wie folgt PIN 1 Phantom Ground PIN 2 Phantom Power PIN 3...
Seite 76
K+H Vertriebs- und Entwicklungsgesellschaft mBH Article 526399 Auf dem Kessellande 4a 30900 Wedemark Germany www.klein-hummel.com Rev. D - 20080205...