Loading Paper; Connecting The Power Cord; Final Preparations - Sharp AL-2061 Startanleitung

4. LOADING PAPER

Raise the handle of the paper tray and
1
pull the paper tray out until it stops.
Squeeze the lever of paper guide (A) and slide
4
the guide to match with the width of the paper.
Move paper guide (B) to the appropriate slot
as marked on the tray.
(B)

5. CONNECTING THE POWER CORD

If you use the unit in a country other than the country where the
unit was purchased, you will need to make sure that your local
power supply is compatible with your model. If you plug the unit
into an incompatible power supply, irreparable damage to the
unit will result.
Ensure that the power switch of
1
the unit is in the "OFF" position.
Turn the power switch on the left
2
side of the unit to the "ON"
position.
About the scan head
The scan head lamp remains on constantly when the unit is in the ready
condition (when the start ( ) indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality.
At this time, the scan head moves automatically. This is normal and does not
indicate unit trouble.
6. CONNECTIONS
CONNECTING THE TELEPHONE LINE CORD
Plug one end of the telephone line cord into the
jack on the machine marked "LINE." Plug the
other side into a standard (RJ11C) single-line
telephone wall jack. Be sure not to plug this
telephone line cord into the "TEL" jack. The
"TEL" jack is used to attach an extension
telephone or answering machine to the machine.
(See "CONNECTING OTHER DEVICES")
If your area experiences a high incidence of lightning or power
surges, we recommend that you install surge protectors for the
power and telephone lines. Surge protectors can be purchased
from your retailer or at most telephone specialty stores.

7. FINAL PREPARATIONS

CONNECTING OTHER DEVICES
If desired, an answering machine or external telephone can be connected to the
machine through the telephone jack, labeled "TEL," on the rear of the machine.
• Connecting an answering machine to the machine allows you to receive both
voice and fax messages when you are out. To use this feature, first change the
outgoing message of your answering machine, and then set the reception
mode of the machine to "A.M." (Answering Machine mode) when you go out.
If you are using distinctive ringing with an answering machine,
you do not need to follow the procedure described below.
(Please note that when distinctive ringing is used, the
answering machine must be distinctive ring compatible.)
2
Rotate the pressure plate lock in the direction
2
of the arrow to remove it while pressing down
the pressure plate of the paper tray.
Fan the paper and insert it into the tray.
5
Make sure the edges go under the
corner hooks.
(A)
OFF
ON
Store the pressure plate lock which has been
3
removed in step 2. To store the pressure plate lock,
rotate the lock to fix it on the relevant location.
Gently push the paper tray back into the unit.
6
Comments:
1.It is advisable to keep the length of the message under 10 seconds. If it is
too long, you may have difficulty receiving faxes sent by automatic dialing.
2. Your callers can even leave a voice message and send a fax message on the
same call. Modify your outgoing message to explain that this can be done by
pressing their [START] key (
• You can connect an extension phone to the machine to make and receive calls
like any other extension phone on your line. Even if you pick up the extension
phone and hear a fax tone, the machine will automatically cut in and take over
the line. Note, however, if you also have a PC modem on the same line, you
must turn on the Remote Reception function, and deactivate the Fax Signal
Receive function. See "SETTING UP THE MACHINE FOR USE WITH A PC
MODEM" (p.33) and "USING THE REMOTE RECEPTION FUNCTION" (p.34).
The Remote Reception function is initially set to "ON".
8. ABOUT THE OPERATION GUIDES
The operation guides for the machine are as follows:
Start Guide (this manual)
This manual covers the procedures for setup and the safety relations.
Operation Guide for machine (on the AL-2051_AL-2061 User Documentation CD-ROM)
Explains the machine and how to use it as a copier. Also explains how to use the
machine as a printer and scanner for your computer.
Operation Guide for fax (on the AL-2051_AL-2061 User Documentation CD-ROM)
This manual explains the procedures for using the machine as a fax machine.
This manual only explains the fax functions of the machine. For general information
on using the machine, including safety information, installation, paper loading,
removal of paper misfeeds, and peripheral equipment, see the operation guide for
the machine.
How to use the operation guide
Detailed explanations of the functions that can be used on the machine are provided
in the Operation Guide in PDF format.
Insert the supplied CD-ROM into
1
your computer's CD-ROM drive.
Display the contents of the CD-
2
ROM, and open the Operation
Guide file.
* To view the Operation Guide in PDF format, Adobe
® ®
Acrobat Reader of Adobe Systems Incorporated is required.
® ®
Adobe Reader can be downloaded from the following URL:
http://www.adobe.com/
A paper form operation manul can be obtained from your authorized SHARP
dealder or upon request by contacting SHARP.
SHARP Manufacturing France - Customer Documentation Department
Route de Bollwiller
68 360 SOULTZ - FRANCE
or by fax (+33) 3.89.74.87.78
Please inform the model name, the serial number of the machine and the
language needed. Do not forget to add your name and your address.
• Be sure that paper is free of rips, dust,
wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is
the same size and type.
• When loading paper, ensure there is no
space between the paper and the
guide, and check if the guide is not set
too narrow causing the paper to bend.
Loading paper in these ways will result
in document skew or a paper jam.
) after leaving their voice message.
User Documentation
CD-ROM
Manual English
® ®
Reader
Operation
Guide file
(PDF)
or