Scheppach LMP460SP Originalbetriebsanleitung Seite 25

Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 83,5 dB(A)
pA
Sound power L = 94,3 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (left/right) = 7,5 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
7. Before first use
Before starting the equipment
Assemble the components
Some parts of the mower are disassembled. For
quick and easy assembly, read and follow the inst-
ructions below.
Important! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
• 1 liter measuring jug (oil/petrol resistant)
• petrol can (5 liters is sufficient for approx. 6 opera-
ting hours)
• funnel (suitable for the tankʼs petrol filler neck)
• household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
• petrol suction pump (plastic, available from DIY
stores)
• oil can with hand pump (available from DIY stores)
• 0,6 liter of engine oil (SAE 30)
Assembly
1. Unpack the mower and attachment parts and
check the delivery is complete.
2. Attach the lower push bar to both sides of the
mower with one screw (a) and one star grip nut
(e) each. Make sure that the cables, which will be
attached later, are not been bent (Fig. 2-4).
3. Attach the upper push bar (4) on the lower push
bar with one quick-release lever (5) and one plastic
nut each on both sides (Fig. 5). Note the correct
alignment of the quick-release lever bracket ensu-
ring the quick-release function remains intact.
4. Insert the pull start handle in the designated hook
as shown in Fig. 6.
5. Fix the cables to the push bar with the cable clips
(g) provided (Fig. 7).
6. Grass box (16) - open it up and click the plastic
clips into position on the frame (Fig. 8).
7. Mowing with grass box:
Lift the discharge flap (Fig.1/No. 15) with one hand
and hang in the grass box (Fig.1/No. 16) as shown
Fig. 9.
2
8. Mowing with side discharge:
Lift the side discharge flap and mount the side
discharge cover (18) (Fig. 10). If the grass box is
attached, remove it and insert the mulch insert.
9. Mulching:
If the grass box (16) is attached, remove it and
insert the mulch insert (19) as shown in Fig. 11-13.
Caution:
The side discharge cover must not be installed.
Setting the cutting height
m CAUTION!
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• Before beginning to mow, check to ensure if the
blade is not blunt and that none of the fasteners
are damaged.
• To prevent any imbalance, replace blunt and/or da-
maged blades as a set only. Before checking, first
switch off the engine and pull the spark plug boot.
• The cutting height is adjusted with the wheel height
adjustment lever (Fig.1/ Item 14). 8 different cutting
heights can be selected.
• Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position. (Fig. 14)
8. Operation
m CAUTION!
The mower is delivered without engine oil and petrol.
Fill in petrol (unleaded gasoline) and engine oil (10W
30 / SAE 30) before starting the engine. The oil level
must be checked each time before mowing.
• In order to avoid any unintentional start-ups, the
lawn mower is equipped with an engine brake
(Fig. 1/ Item 3) which must be actuated before the
engine is started. When the engine control lever is
released it must return to its initial positionand and
the engine is automatically switched off.
• Push the engine brake lever (3) to the handle and
give the starter cord (17) a vigorous pull.
Attention:
When you pull the starting rope the cutting blade
rotates even when dissolved motor brake lever.
Make sure that there are no body parts in danger
zone of cutting blade.
• When the engine is running, push the drive lever
(2) to the handle (1) in order to engage drive.
• Before mowing run through this operation several
times in order to ensure that the machine is wor-
king properly.
m WARNING
The blade has to be come to a complete stop be-
fore adjustment and/or repair work is carried out.
Always switch off the engine before adjustments,
maintenance and repairs.
m Note!
Fig. 15
• Engine brake (3): Use the lever to stop the engine.
When you release the lever the engine and the bla-
de stop automatically.
DE GB FR
FR FR
25 І 48