Technical Specifications; Input Specifications; Output Specifications - TRACOpower TSP 070-112 Bedienungsanleutung

6. Technical Specifications

6.1 Input Specifications

Order- * Input
code voltage
Model range
100-240VAC
TSP 070-112
TSP 090-124 85-264VAC
TSP 090-124N
(47-63 Hz)
TSP 140-112 100-120VAC/
TSP 180-124
220-230VAC
85-132 VAC/
TSP 360-124
187-264 VAC
(47-63 Hz)
TSP 600-124
Auto range
* Observe output current derating at operation below an input voltage of 110VAC (see Fig. 4.2).
** Output voltage adjustable
*** Maximum current at Vout nom.

6.2 Output Specifications

Regulation
- Input Variation (Line Regulation)
- Load Variation (Load Regulation)
Output Voltage adjustable Range
with Potentiometer
Ripple and Noise (20MHz Bandwidth)
Overload protection
Electronic Short Circuit Protection
Parallel Operation
Over Voltage Protection (OVP)
Hold-up Time
Reverse Voltage Protection
Status Indicator (two colours)
Power Good Signal
Max. Capacitive Load
max. ** Output
Output- voltage
power Factory Set ±1%
78 Watt 12 VDC
90 Watt 24 VDC
90 Watt 24 VDC
156 Watt 12 VDC
180 Watt 24 VDC
360 Watt 24 VDC
600 Watt 24 VDC
V - V
in min in max
10% - 100% of I
out max
12 V Model
24 V Model
at V und I
in nom out max
Thermal protection
Continuous
all Models; User selectable standard mode
and parallel mode by jumper on PCB
Trigger point at
at full load and V = 115VAC
in
at full load and V = 230VAC
in
Trigger threshold
Active output signals
(referenced to –V
out
Relay output DC-OK = Contact closed
Tel: +41 43 311 4511
Jenatschstrasse 1
Fax: +41 43 311 4545
CH-8002 Zürich
*** Output Input current
current at full load typ.
I 115 VAC
out max
6.5 A 2.0 A
3.75 A 2.1 A
3.75 A 2.1 A
13.0 A
2.5 A
2.8 A
7.5 A
15.0 A 5.0 A
25.0 A 10.0 A
0.5% max
0.5% max
2.0% in parallel operation
12 - 14 VDC
24 - 28 VDC
200mV pk-pk max
Automatic restart
Constant current. Automatic restart
up to 5 Power Supplies possible
(Jumper position see Fig. 5.1, 5.2, 5.3 & 5.4)
20VDC
35VDC
10ms min.
20ms min
35VDC (40VCD < 1 sec.)
Green LED Normal operation
Red LED Output failure – if AC input mains is present
TSP xxx-112
TSP xxx-124(N) 18 – 22VDC
TSP 070-112 11.0VDC ±1.0VDC / 20mA max.
) TSP 140-112 11.0VDC ±1.0VDC / 40mA max.
TSP 090-124(N) 22.0VDC ±2.0VDC / 10mA max.
TSP xxx-124 22.0VDC ±2.0VDC / 20mA max.
30VDC / 1.0A max.
unlimited
sales@traco.ch
www.tracopower.com
Inrush current
max. at +25°C (<2ms)
230 VAC 115 VAC 230 VAC
1.0 A
1.0 A 12.0 A 20.0 A
1.0 A
1.4 A
13.0 A 25.0 A
1.5 A
2.5 A 16.0 A 25.0 A
5.0 A 25.0 A 30.0 A
TSP xxx-112
TSP xxx-124
9 – 11VDC
Date:
10 October 2005
Issue: 2.1
English
Efficiency
typ.
at 230VAC
82.0 %
85.0 %
85.0 %
85.0 %
88.0 %
87.0 %
89.0 %
Page
7
Seite