Safety Information; Meaning Of The Safety Information; Pictograms And Symbols - Parkside Performance Ppbs 3 B2 Originalbetriebsanleitung

– Hole ...............................................25.4 mm
– Max. permitted speed ............. 10000 min
Sound pressure level (L
......................................... 98.8 dB; K
Sound power level (L
WA
– Guaranteed ......................................113 dB
– Measured ..............110.3 dB; K
Vibration (a ) 3-blade steel cutter
h
– Multifunction handle
...................................7.762 m/s²; K=1.5 m/s²
– Handle ....................7.651 m/s²; K=1.5 m/s²
Vibration (a ) 22-tooth clearing blade
h
– Multifunction handle
...................................7.862 m/s²; K=1.5 m/s²
– Handle ....................7.989 m/s²; K=1.5 m/s²
Vibration (a ) Spool
h
– Multifunction handle
...................................7.468 m/s²; K=1.5 m/s²
– Handle ....................7.532 m/s²; K=1.5 m/s²
Levels of noise and vibration were determ-
ined according to the standards and regula-
tions in the declaration of conformity.
The specified total vibration value was de-
termined according to the following stand-
ard: ISO 22867
The specified noise emission values were
determined in accordance with the following
standard: ISO 22868
The values have been determined accord-
ing to a standardised test procedure and can
be used to compare one tool with another.
The specified total vibration value and the
stated specified noise emission value can
also be used for a provisional assessment of
the load.
WARNING! The vibration and noise emis-
sions may deviate from the specified val-
ues during actual use of the device, depend-
ing on how the device is being used. Safety
measures for the protection of the operat-
or are to be determined that are based on
an estimate of the actual vibration load un-
der the real operating conditions (for this, all
parts of the operating cycle are to be taken
into account, for example, times in which the
device is turned off, and those during which
it is turned on but running without a load).
X 20 V TEAM
The device is part of the X 20 V TEAM
series and can be operated with batteries
of the X 20 V TEAM series. Batteries of the
-1
)
pA
=3 dB
pA
)
=2.48 dB
WA
X 20 V TEAM series may only be charged
using chargers of the X 20 V TEAM series.
We recommend that you operate this ap-
pliance with the following batteries only:
PAP 20 B1, PAP 20 B3, Smart PAPS 204 A1,
Smart PAPS 208 A1, Smart PAPS 2012 A1
We recommend charging these bat-
teries with the following chargers:
PLG 20 A1, PLG 20 A3, PLG 20 A4,
PLG 20 C1, PLG 20 C2, PLG 20 C3,
PLG 201 A1, PDSLG 20 A1, PDSLG 20 B1,
Smart PLGS 2012 A1
Rechargeable battery and charger technical
data: See separate manual.

Safety information

This section deals with the basic safety in-
structions for using the device.
WARNING! Injury and property damage
due to improper handling of battery. Observe
the safety information and notes on charging
and proper use as shown in the instruction
manual for your battery and charger from the
series X 20 V TEAM. A detailed description
of the charging process and further informa-
tion can be found in these separate operat-
ing instructions.

Meaning of the safety information

DANGER! If you do not observe this
safety instruction, an accident will occur.
The result of which is severe bodily injury or
death.
WARNING! If you do not observe this
safety instruction, an accident may occur.
The result of which is likely severe bodily in-
jury or death.
CAUTION! If you do not observe this
safety instruction, an accident will occur. The
result of which is likely minor or moderate
bodily injury.
NOTICE! If you do not observe this safety in-
struction, an accident will occur. The result
of which is possible damage to property.

Pictograms and symbols

Symbols on the device
Attention!
Read the instruction manual
GB
MT
33