Princess ESE POD Benutzerhandbuch Seite 5

Coffee Volume Setting
Espresso cup setting
1. When the machine is ready (buttons are solid blue).
2. Press and hold the Espresso button for 5 seconds.
3. The light will blink. Keep holding to brew the amount you want.
4. Release the button to stop. The machine will remember this amount.
Lungo cup setting
1. Press and hold the Lungo button for 5 seconds.
2. The light will blink. Keep holding to brew the amount you want.
3. Release the button to stop. The machine will remember this amount.
Enter standby mode
Press and hold the Power button for 3 seconds. The machine will enter standby mode (red light).
•
Reset to default coffee volume
While in standby mode (red light), press both Espresso and Lungo buttons at the same time. The lights
•
will blink 3 times. The coffee volume is now reset to factory settings.
Coffee Temperature Setting
You can adjust the coffee temperature in 7 levels: default, 4 higher, and 2 lower.
This can only be done when the machine is in standby mode (red power light).
Lower the temperature
Press and hold the Espresso button:
• Blinks 2 times = 1 level lower
Press again: blinks 1 time = 2 levels lower
•
Raise the temperature
Press and hold the Lungo button:
• Blinks 1 time = 1 level higher
Press again: blinks 2 times = 2 levels higher
•
Press again: blinks 3 times = 3 levels higher
•
Press again: blinks 4 times = 4 levels higher
•
Standby Time Setting
You can choose how long the machine waits before going into standby.
This can only be done when the machine is in standby mode (red power light).
1. Press and hold the Power and Espresso buttons together for 3 seconds.
The Espresso and Lungo lights will blink 3 times.
•
2. Press the Espresso button to cycle through options:1 blink = standby after 25 minutes
• 2 blinks = standby after 4 hours
• 3 blinks = standby after 8 hours
•
4 blinks = no standby
Press again to return to 1 blink (25 minutes)
•
Pre-Infusion Setting
Pre-infusion helps improve flavor for some coffee pods.
This can only be done when the machine is in standby mode (red power light).
1. Press and hold the Power and Lungo buttons together for 3 seconds. The machine enters pre-infusion
setting mode.
2. Press the Espresso button to turn off pre-infusion.
3. Press the Lungo button to turn on pre-infusion.
4. Press the Power button to save and exit.
© Princess | ESE POD Coffee Machine 8 | 01.249420.01.001
CLEANING AND MAINTENANCE
Water Tank C y
1. Remove the tank.
2. Rinse it with clean water.
3. If needed, wipe it with a clean cotton cloth, then rinse again.
Drip Tray A
8
1. Remove the tray.
2. Rinse it with clean water.
3. If needed, wipe it with a clean cotton cloth, then rinse again.
Machine Exterior
1. Wipe the outside of the machine with a soft, slightly damp cotton cloth.
2. Always turn off the power and unplug the machine before cleaning.
TROUBLESHOOTING
Problem Possible cause
No lights on the machine Power is not connected
No coffee comes out Water tank is empty
Used capsule is still inside
Button is pressed but machine
Sliding door A
doesn't work closed
Coffee is not hot enough Cup is cold
Sliding door cannot open Machine is still under pressure
Loud noise during brewing Water tank is empty or not
installed correctly
Machine turns off by itself Auto shut-off feature
All lights flash red
System error
DISPOSAL
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities. Contact your local government for information
regarding the collection systems available. If electrical appliances are
disposed of in landfills or dumps, hazardous substances can leak into
the groundwater and get into the food chain, damaging your health and
well-being. When replacing old appliances with new ones, the retailer is
legally obligated to take back your old appliance for disposals at least free
of charge.
Gebruikshandleiding
d
Gebruikshandleiding
Possible solution
Check if the plug is properly
inserted into the socket
Fill the water tank C
y
with water
Remove the used capsule and
insert a new one
Close the sliding door completely
9
is not fully
Run hot water through the
machine to warm the cup before
brewing
Turn off the machine and wait
for the pressure to release, then
try again
y
Make sure the water tank C
has water and is placed properly
The machine shuts down
automatically after 25 minutes of
no use to save energy
Turn off the machine, wait 1
minute, then turn it back on
9