Nordpeis N-36A Exclusive Montageanleitung Seite 14

around the clock increase pollution as well as the risk
for a fire in the chimney. Never allow the insert or flue
to become glowing red. Turn off the air vent control
should this happen. Regulation of the air vent control
takes some experience, but after a little while a natural
rhythm for the fire will be found.
WARNING:
Never leave the air control in ignition mode for pro-
longed periods as this may lead to overheating.
IMPORTANT! Always remember to open the air
vent control (preferably also the door) before new
wood logs are inserted into a hot burn chamber.
Let the flames get a good grip on the wood before
the air control setting is reduced.
When the draught in the chimney is low and
the vent is closed, the gas from the firewood
can be ignited with a bang. This can cause
damage to the product as well as the immediate
environment.
6. Maintenance
Cleaning and inspection
The insert should be inspected thoroughly and cleaned
at least once per season (possibly in combination
with the sweeping of the chimney and chimney pipes).
Ensure that all joints are tight and that the gaskets are
rightly positioned. Exchange any gaskets that are worn
or deformed.
Remember that the insert must always be cold when
inspected.
Ashes
The ashes should be removed at regular intervals.
Be aware that the ashes can contain hot ember even
several days after the fire is finished. Use a container
of non-combustible material to remove the ashes. It is
recommended to leave a layer of ashes in the bottom
as this further insulates the burn chamber. Take care
with the Thermotte plates when the ashes are removed,
particularly when using an ash shovel, so as not to
damage them.
Thermotte™
The insulation plates (Thermotte - FIG 3) are classi-
fied as "wear and tear" parts which will require to be
exchanged after some years. The wear time will depend
on the individual use of your product.
Nordpeis offers a one-year warranty on these parts.
After this, replacements can be purchased.
In case it is necessary to take out the insulation plates,
this is done in following order.
A. Smoke baffle
B. Back plate
C. Ash pan cover
D. Front plate
14
E. Side plate left
F. Side plate right
G. Bottom plate left
H. Bottom plate right
I. Bottom plate front corner
Please note: Wood logs that are too long can cause
additional strain and crack the plates, due to the tension
created between the side plates.
Door and Glass
Should there be any soot on the glass it may be
necessary to clean it. Use dedicated glass cleaner,
as other detergents may damage the glass. (NB! Be
careful, even dedicated glass cleaner can damage the
varnish on the door frame and the gaskets). A good
advice for cleaning the glass is to use a damp cloth or
kitchen roll paper and apply some ash from the burn
chamber. Rub around the ash on the glass and finish off
with a piece of clean and damp kitchen roll paper.
NB! Only clean when the glass is cold.
Check regularly that the transition between the glass
and the door is completely tight.
Periodically, it may be necessary to change the gaskets
on the door to ensure that the burn chamber is air tight
and working optimally. These gaskets can be bought as
a set, usually including ceramic glue.
CERAMIC GLASS
CANNOT BE
RECYCLED
Ceramic glass should
be disposed of as resid-
ual waste, together with
pottery and porcelain
Recycling of the ceramic glass
Ceramic glass cannot be recycled. Old glass, breakage
or otherwise unusable ceramic glass must be discarded
as residual waste. Ceramic glass has a higher melting
temperature, and can therefore not be recycled together
with glass. If mixed with ordinary glass, it would damage
the raw material and could, in worst case end the
recycling of glass. It is an important contribution to the
environment to ensure that ceramic glass does not end
up with the recycling of ordinary glass.
Packaging Recycle
The packaging accompanying the product should be
recycled according to national regulations.
7. Warranty
Use replacement parts recommended only by the
GB
Warning!
Manufacturer.