Conrad Electronic TLV-9600 Bedienungsanleitung Seite 48

The use of the 4 port VideoSplitter is only allowed in dry interiors.
Please note, that you render yourself liable to prosecution if you are
watching unknown people without their knowledge or their consent
with this camera.
This product is only licensed for the connection to a 12 volts direct
voltage.
Any use other than the one previously described is not permitted
and can lead to damages on the product.
Moreover, this involves dangers, such as e.g., short-circuit, burns,
electric shock, etc.
No part of the product may be modified or rebuilt.
Always observe the safety instructions and technical data.
Table of contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Prescribed Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Output (2) "QUAD ONLY" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Output (1) "Switch" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Maintenance and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
16
Problem Solution
No picture Is the operating voltage of the VideoSplitter polar-
ized correctly?
Is the TV/monitor switched on and ready for use?
Has the right AV input or on the monitor the cor-
rect input been chosen?
Is the VideoSplitter supplied with the correct direct
voltage? If this is not the case, it can lead to mal-
function or to complete failure of the VideoSplitter.
Is the VideoSplitter connected to the to the power
supply and the TV/monitor as described earlier in
this manual in chapter "Connection"?
Has an individual camera picture been selected to
which no camera was connected?
Repairs other than the ones previously described are
only to be carried out by an authorised specialist.
Technical Data
Operating voltage:
Current consumption:
Inputs:
Outputs:
Video output:
Automatic picture switchover:
12 V=
approx. 250 mA
4 x BNC
2 x BNC
1 Vss / 75 Ω
4 seconds
25