ZAMEL exta free RZB-04 Bedienungsanleitung Seite 9

RADIO TRANSMITTERS POGRAMMING - CHANNEL 2
Press PROG push-button of ROP-02 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button. Wait (for about 5 sec-
onds) till LED red diode switches on (first signal pulsates, next the signal is constant).
Choose one out of five ROP-02 operating modes and programme the device in the
same way as for channel 1. CAUTION: For the monostable mode, press the button
on the remote before pressing PROG push-button.
TIME PROGRAMMING
Press PROG push-button of ROP-02 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button. Wait (for about 5 sec-
onds) till LED red diode switches on (first signal pulsates, next the signal is constant).
Wait again (for about 5 seconds) till LED red diode switches on (first signal pulsates,
next the signal is constant).
for CHANNEL 1:
LED red diode switches off and then switches on (signal pulsates). Every LED diode
pulse equals 1 second.
diode flashes) press PROG push-button and then release it - TIME IS ADDED.
for CHANNEL 2:
(first signal pulsates, next the signal is constant).
02 device and then release it. LED red diode switches off and then switches on (signal
pulsates). Every LED diode pulse equals 1 second.
(the number of LED red diode flashes) press PROG push-button and then release
it - TIME IS ADDED.
Maximum time is 18 hours for every channel.
RADIO TRANSMITTERS DELETION
Press PROG push-button of ROP-02 device for a longer time.
red diode switches on (signal pulsates) and then it switches off.
button in ROP-02 - MEMORY IS DELETED.
COOPERATION AND OPERATING RANGE
ROP-02 ROP-04 ROB-01 SRP-02 SRP-03 RWG-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02 180 m
RNK-04 180 m
P-256/8 230 m
P-257/4 (2) 180 m
RNM-10 230 m
RNP-01 160 m
RNP-02 160 m
RNL-01 160 m
RTN-01 200 m
RCR-01
160 m
RXM-01 230 m
* 1-channel transmitters do not cooperate with roller blind controllers
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles.
If there are some obstacles between a transmitter and a receiver, it is advisable to decrease the range accord-
ing to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal:
from 90 to 100%, glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio
and television transmitters, GSM transmitters set close to a device system have also a negative influence on
the range.
Press PROG push-button of ROP-02 device and then release it.
After the adjusted time is finished (the number of LED red
Wait again (for about 5 seconds) till LED red diode switches on
200 m 200 m 200 m
200 m 200 m 200 m
250 m 250 m 250 m
200 m 200 m 200 m
250 m 250 m 250 m
180 m 180 m 180 m
180 m 180 m 180 m
180 m 180 m
200 m 200 m 200 m
180 m 180 m
250 m 250 m 250 m
Press PROG push-button of ROP-
After the adjusted time is finished
200 m 250 m
200 m 250 m
250 m 300 m
200 m 250 m
250 m 300 m
180 m 200 m
180 m 200 m
-* -* 200 m
200 m 250 m
-* -* 200 m
250 m 300 m
After 5 seconds LED
Release the push-
250 m 250 m 180 m
250 m 250 m 180 m
300 m 300 m 230 m
250 m 250 m 180 m
300 m 300 m 230 m
200 m 200 m 160 m
200 m 200 m 160 m
200 m 200 m 160 m
250 m 250 m 200 m
200 m 200 m 160 m
300 m 300 m 230 m
250 m
250 m
300 m
250 m
300 m
200 m
200 m
200 m
250 m
200 m
300 m