Specifications - Makita BCS550 Betriebsanleitung

ENGLISH
1. Red part
2. Button
3. Battery cartridge
4. Lever
5. A position
6. Cutting line
7. Base
8. Switch trigger
9. Lock-off lever

SPECIFICATIONS

Blade diameter
Max. Cutting depth
No load speed (min
Overall length
Rated voltage
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in mild steel and aluminum
only with appropriate saw blades.
CORDLESS METAL CUTTER
SAFETY WARNINGS
DANGER:
1. Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the tool,
they cannot be cut by blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
5. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring. Contact with a "live"
wire will also make exposed metal parts of the power
tool "live" and shock the operator.
6. When ripping always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance for blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
4
Explanation of general view
10. Lamp
11. Shaft lock
12. Hex wrench
13. Hex bolt
14. Outer flange
15. Saw blade
16. Inner flange
17. Cup washer
18. Front grip
Model
-1
)
Net weight
that do not match the mounting hardware of the tool
ENE066-1
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolts. The blade washers and bolt were specially
designed for your tool, for optimum performance and
safety of operation.
GEB058-1
9. Causes and operator prevention of kickback;
- Kickback is a sudden reaction to a pinched, bound
or misaligned blade, causing an uncontrolled tool to
lift up and out of the workpiece toward the operator.
- When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator.
- If the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the workpiece causing the
blade to climb out of the kerf and jump back toward
the operator.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below.
• Maintain a firm grip with both hands on the tool
and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the tool to jump backwards, but
kickback forces can be controlled by the operator, if
proper precautions are taken.
• When blade is binding, or when interrupting a
cut for any reason, release the trigger and hold
the tool motionless in the material until the
blade comes to a complete stop. Never attempt
to remove the tool from the work or pull the tool
19. Rear handle
20. Sight grooves
21. Clamping screw
22. Rip fence (Guide rule)
23. Limit mark
24. Brush holder cap
25. Screwdriver
BCS550
136 mm
51 mm
3,600
348 mm
2.6 kg
D.C. 18V