First Use - AEG DAB+ 4153 Bedienungsanleitung

English
40 40
Reverse (not shown)
AC 230 V ~ 50 Hz Mains connection
AUX IN Input
Headphone jack
Battery compartment
Start-up of the Device
• Select a suitable location for the device, such as a dry,
flat, non-slip surface on which it is easy to operate the
machine.
• Ensure that the device is sufficiently ventilated!
• Sensitive surfaces, such as the display, might be protected
with films. Remove such films.
Power Supply
1. Ensure that the voltage is the same as that indicated on
the model identification plate.
2. Connect the power cable supplied (see battery compart-
ment if necessary) to a properly installed safety power
socket and the mains connector AC 230 V ~ 50 Hz on the
back of the machine.
NOTE:
• If the unit is not used for a long period of time, unplug
the mains plug from the socket.
• If the power supply gets disconnected, the time/date
settings will be lost.
Battery Operation (not supplied)
1. Open the lid of the battery compartment on the back.
2. Insert 6 batteries of type AA / R 6 1.5 V. Please ensure
that the polarity is correct (see the floor of the battery
compartment)!
3. Then close the battery lid.
NOTE:
When a mains cable is connected the batteries are auto-
matically switched off.
CAUTION:
• Batteries can leak battery acid. If the device is out of use
for a long period of time, remove the batteries.
• Different battery types or new and used batteries must
not be used together.
• Batteries are not to be disposed of together with
domestic wastes. Dispose of the used batteries at the
relevant collection bin or at your dealer' s .
WARNING:
The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like. Danger of explosion!
DAB+4153_IM

First Use

1. Fully extend the telescopic antenna. Stand it upright for
initial installation.
2. Use button POW / FUN to turn on the device.
3. The device automatically searches for DAB stations.
"Suchen..." and a progress bar appears on the display.
The figure on the right of the display shows the number
of radio stations found. The first alphanumeric DAB
station is played.
When playing a radio station, the time and date is taken
from the broadcasting service. If the device does not re-
ceive DAB stations in your location, set the time manually
as described in "Setting the time and date manually".
Changing the OSD language
The factory default of the OSD menu is German. To change
the language, proceed as follows:
1. Press the MENU button.
2. Select the menu item "Hauptmenü" with the TUNE
controller. Confirm with the ENTER button.
3. Select the menu item "Sprache" with the TUNE control-
ler. Confirm with the ENTER button.
4. Select the desired language with the TUNE controller.
Confirm with the ENTER button.
NOTE:
The menu is described with the selected language
"ENGLISH" in the instruction manual.
Setting the time and date manually
If the device is in standby mode, the display will indicate the
time and date. This can be set as follows:
• With the TUNE controller you make the settings.
• The current setting flashes.
• With the ENTER button you confirm your setting.
1. Keep the POW / FUN button pressed for about 3 seconds
in order to switch the device to standby.
2. Press the MENU button. The menu item "<Clock
Setting>" will appear on the display.
3. Confirm with the ENTER button. The notification "24
Hour" and the current date will appear on the display.
4. Set the time display format (24 or 12 hours), the hours, the
minutes, day, month, and year one after the other.
NOTE:
• In 12 hour display AM = morning, PM = afternoon
appears.
• The storage of the time and date will be erased once
the power supply has been interrupted.
19.05.16