Operation - Makita DF010D Betriebsanleitung

Guideline for clutch auto-stop
Work range of
Increments on
clutch auto-stop
adjusting ring
for fastening
High Low
torque
speed speed
Clutch auto-
stop works
Clutch auto-
stop does not
work
Increments
When driving
1 - 3
machine
4 - 8
screws
9 - 18
19 - 21
Lighting up the front lamp (Fig. 6 & 7)
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the light, slide the lamp switch to the A position.
To turn off the light, slide the lamp switch to the B position.
Even if you leave the lamp on, the light will automatically
turn off after 5 minutes.
Checking the remaining battery capacity,
auto-stop
The lamp signals by flickering when the battery power is
almost used up during use.
At this time, recharge the battery or replace the battery
with a fully charged one.
ASSEMBLY
CAUTION:
• Always be sure that the lock button is in the locked
position B and the battery cartridge is removed before
carrying out any work on the tool.
Installing or removing driver bit or socket
bit (Fig. 8)
Use only the driver bit or socket bit shown in the figure.
6
Fastening torque
Approx. 0.3 N·m
1
(Approx. 3 Kgf-cm)
Approx. 0.82 N·m
5
(Approx. 8.4 Kgf-cm)
Approx. 1.35 N·m
9
(Approx. 13.8 Kgf-cm)
Approx. 1.88 N·m
13
(Approx. 19.2 Kgf-cm)
Approx. 2.41 N·m
17
(Approx. 24.6 Kgf-cm)
Approx. 2.9 N·m
21
(Approx. 30 Kgf-cm)
Low speed
Approx. 5 N·m
(Approx. 49 Kgf-cm)
High speed
Approx. 1.5 N·m
(Approx. 14.7 Kgf-cm)
Guideline for machine
screw diameter
2.5 mm
3 mm
4 mm
5 mm
Do not use any other driver bit or socket bit.
For European and North & South American countries,
Australia and New Zealand
Use only these type of bit. Follow the
A=12mm
procedure (1).
B=9mm
(Note) Bit-piece is not necessary.
For other countries
To install these types of bits, follow the
A=17 mm
procedure (1).
B=14 mm
(Note) Makita bits are these types.
To install these types of bits, follow the
A=12 mm procedure (2).
B=9 mm (Note) Bit-piece is necessary for installing
the bit.
1. To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will
go. Then release the sleeve to secure the bit. (Fig. 9)
2. To install the bit, pull the sleeve in the direction of the
arrow and insert the bit-piece and bit into the sleeve
as far as it will go. The bit-piece should be inserted
into the sleeve with its pointed end facing in. Then
release the sleeve to secure the bit. (Fig. 10)
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
• If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a
pistol type which is selectable according to the conditions
of workplace and screwdriving. (Fig. 11)
Screwdriving operation (Fig. 12)
CAUTION:
• Adjust the adjusting ring to the proper torque level for
your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Then switch the tool on. When
the clutch cuts in, the motor will stop automatically. Then
release the switch.
CAUTION:
• Make sure that the driver bit is inserted straight in the
screw head, or the screw and/or bit may be damaged.
NOTE:
• When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.