Technical Specifications - Faac 422 Bedienungsanleitung

422
PRELIMINARY NOTES
Ensure that the structure of the gate
current regulations and that the movement
and without friction.
Make all necessary adjustments
stops before installing the automation
Installation must be carried
regulations.
INSTALLATION INSTRUCTIONS
1) Fit the rear mounting bracket
Fig. I and Table A.
N.B.: The installation dimensions should be strictly adhered
Failure to do so may result in the incorrect
the operator.
2) Attach the operator to the rear mounting
Fit the cable cover provided
3)
4) Connect the electrical cables
(see relevant instructions).
5) Remove the breather screw as illustrated in Fig. 3.
6) Mount the safety guard
illustrated in Fig. 3.
Keeping the operator in a horizontal position, cycle five or six
7)
times in order to check the smooth
rod.
N.B.: Shouldthe piston rod tend tojudderitwill
perform further cycles, bleeding
operation is obtained.
8) After bleeding, unlock the operator
gently pressing the safety cover down and sliding it in the
direction of the arrow.
insert the unlocking key provided
it at least once in an anti-clockwise
IMPORTANT: IT IS ONLY POSSIBLE TO REMOVE
IN ITS ORIGINAL POSITION (LOCKED
TURNED THE KEY 3600 (UNLOCKED
9) Withtheoperatorunlocked
to the end of its stroke and then reduce the length by 5 mm
(Fig. 5).
10) Assemble the front bracket
11) Close the gate and, keeping the operator
position, locate and mark the position of the front bracket on
the leaf (Fig. 7).
12) Attach the front bracket
To prevent any weld spatter from damaging
N.B.:
during installation. disconnect
bracket while welding.
13) Reconnect the piston rod to the front bracket.
TECHNICAL SPECIFICATIONS
MODEL
CBC
POWER SUPPLY (V)
ABSORBED POWER (W)
CURRENTDRAWN (A)
MOTOR RPM
THERMAL CUT-OUT (oc)
PUMP DELIVERY(l/rnin)
PISTONROD SPEEDccm/sec)
MAX USAUE PSIONRODLENGTH
DUTY CYCLE
MAX. THRUST ( Kg)
MAX LEAF LENGTH (m)
HYDRAULIC LOCK
TYPE OF OIL
OIL CAPACITY (D
WEIGHT (Kgs)
ELECTRONIC CONTROL BOX
is in compliance
of the leaves iseven
including the fitting of gate
equipment.
out in compliance with current
to the gate post as shown in
operation
bracket (Fig. 2).
as illustrated in Fig. 3.
to the electronic control
onto the unlocking device
operation of the piston
be necessaryto
off the air until a smooth
(Fig. 4) by:
into the lock and turn
direction.
THE KEY WHEN IT IS
LEAF) OR AFTER HAVING
LEAF)
withdrawthe piston rodbyhand
on the piston rod (Fig. 6).
in a horizontal
to the leaf (Fig. 8).
the rod
the piston rod from the
422 PED.
CBC
CBAC SBSÆ
220± 50-60Hz
1400
100
0.75 1.5
2
160
see Fig. 10
570
1.8 2.5 3 1.2
YES
FAAC OIL XD 220
0.8
0.9
7 6.5
401 MPS (hdLJded)
ld) Open the leaf by hand in order to check that the system is
operating correctly,
with
N.B.: An important
correctly consists in ensuring that the rod is never at the
end of its travel when the gate
closed, but a minimum of 5 mm away from this limit.
15) Mount the piston rod cover (Fig. 9).
16) Relock the operator
will go and returning
remove it.
It is necessary to grease all the pins.
N.B..
ADJUSTMENT OF THE ANTI-CRUSHING
to.
The operator is equipped
of
which ensures that
force or in the event of persons or objects being caught in the
path of the gate.
The sensitivity with which this device
by turning the bypass
box unscrewing the fixing screws on the unlocking device as illustrated
in Fig. II.
Closing thrust is governed
Opening thrust is governed
as
Turn the screws clockwise
Turn the screws anti-clockwise
IMPORTANT: ADJUSTMENTS
IMPOSED BY CURRENT REGULATIONS.
IMPORTANT: WHEN REPOSITIONING
KEEP THE LOCK IN ITS ORIGINAL
THIS PROCEDURE
THE UNIT.
It ispossible to fit security seals to the fixing screws. Thiswill
N.B.:
prevent unauthorized
MAINTENANCE
Check the oil level regularly by making sure that it isapproximately
5 mm below the surface of the bypass flange (Fig. 12).
For low to medium duty cycles an annual inspection issufficient;
For higher duty cycles inspection
Only FAAC XD 220 oil should be used for topping
During maintenance
N.B.:
screws are correctly
5
ENGLISH
adjustment for the operator
leaf is fully open or
by turning the key clockwise
it to its original position in order to
SAFETY DEVICE
with an anti-crushing
movement will stop if met by an opposing
operates can be adjusted
screws. These can
by the red screw.
by the green screw.
to increase torque.
to reduce torque.
MUST REMAIN WITHIN
Bypass
THE RELEASE MECHANISM,
POSITION. FAILURE TO FOLLOW
WILL RESULT IN THE INCORRECT
tampering (Fig. I I),
every 6-8 months isadvisable.
always check
set.
to function
as far as it
safety device
be reached by
THE LIMITS
Fig. 11
OPERATION OF
up.
that the bypass
Fig. 12