Roborock Qrevo Master Bedienungsanleitung Seite 7

Connecting to the App
❶ Download the App
Search for "Roborock" in the App Store or
Google Play or scan the QR code to download
and install the app.
❷ Reset WiFi
Press and hold the and buttons until
you hear the "Resetting WiFi" voice message.
Wait for the power indicator light to flash
blue slowly. The robot will then wait for a
connection.
Note: If you cannot connect to the robot due to your
router configuration, a forgotten password, or any other
reason, reset the WiFi and add your robot as a new device.
❸ Add Device
Open the Roborock App, tap the "Scan to
Connect" or "Search for Device" button and
add your device following the in-app guide.
Notes:
• The actual process may vary due to ongoing app updates.
Follow the guide provided in the app.
• Only 2.4 GHz WiFi is supported.
• If the robot waits more than 5 minutes for a connection,
WiFi will be automatically disabled. If you want to
reconnect, reset the WiFi before proceeding.
Instructions for Use
C
Turning On/Off
Press and hold the button to turn on the
robot. The power indicator light will come
on, and the robot will be on standby.
Press and hold the button to turn off the
robot and complete the cleaning cycle.
Note: The robot cannot be turned off when it is being
charged.
Filling the Water Tank
C1
Lift the clean water tank, open its lid, and
then fill it with tap water to MAX. After filling,
close the lid, lock the latch, and then fit the
tank back in place.
Notes:
• To prevent corrosion or damage, do not use
any disinfectant and only use cleaning solution
recommended by Roborock.
• Do not add too much cleaning solution to prevent the
robot from working improperly due to slipping.
• To avoid deformation, only use cold water.
• If any water stains remain on the outside of the
water tank, wipe them with a soft, dry cloth before
reinstalling the tank.
Starting Cleaning
C2
Press the button to start cleaning. The
robot will plan its cleaning route and in each
room, it firstly draws out zone edges and
then fills the room in a zigzag pattern. In
so doing, the robot cleans all rooms one by
one, thoroughly and efficiently.
07
C2-1—Zone 1 – Cleaned.
C2-2—Zone 2 – Cleaned.
C2-3—Zone 3 – In Progress.
C2-4—Zone 4 – Next Zone.
Notes:
• To make sure the robot returns to the dock automatically,
start the robot from the dock and do not move the dock
during cleaning.
• Cleaning cannot start if the battery level is too low.
Allow the robot to charge before starting a cleanup.
• Before cleaning, tidy cords (including the power cord
of the dock) and valuables from the floor. Loose
items may be dragged by the robot, resulting in the
disconnection of electrical appliances or damage of
cords and property.
• If cleaning is completed in less than 10 minutes, the
area will be cleaned twice.
• If the battery runs low during a cleaning cycle, the
robot will automatically return to the dock. After
charging, the robot will resume where it left off.
• The robot will retract mop cloth mounts to clean the
carpet. You can also set the carpet as a no-go zone in
the app to avoid it.
• Before starting each cleaning task, make sure that the
mop cloths have been properly installed.
Spot Cleaning
Press and hold the button to start spot
cleaning.
Cleaning range: The robot cleans a 1.5 m (4.9 ft) ×
1.5 m (4.9 ft) square area centered on itself.
Note: After spot cleaning, the robot will automatically
return to the starting point and be on standby.
Pause
When the robot is running, press any button
to pause it, press the button to resume
cleaning, and press the button to send it
back to the dock for charging.