Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Fitting the additional fi lter (Fig. 7)
For dry vacuum cleaning always use the supplied
additional fi lter (18). Mount the additional fi lter,
so that no air is sucked through the fi lter cage (4)
without being fi ltered.
Assembling the dirt bag (Fig. 9)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (14). Slip the dirt bag (14)
over the vacuuming hole. The dirt bag (14) is sui-
table for dry-vacuuming only. The dirt bag makes
it easier to dispose of the sucked-in dust.
5.3 Fitting the suction hose (Fig. 3, 10, 11)
Connect the suction hose (10) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8)
Blowing
Connect the suction hose (10) to the blow con-
nector (9)
One or more of the elements which make up the
3-part suction tube (11) can be attached to the
suction hose (10) to extend it. The adapter (17)
must be inserted between the suction tube (10)
and the combination nozzle (12) or crevice nozzle
(16).
5.4 Suction nozzles
Combination nozzle (Fig. 11b)
The combination nozzle (12) is for vacuuming so-
lids and liquids over medium to large areas.
Crevice nozzle (Fig. 11a)
The crevice nozzle (16) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
6. Operation
6.1 On/Off switch (Fig. 1)
Switch position 0:
Off
Switch position I:
On
Anl_TC-VC_2045_S_SPK13.indb 13
Anl_TC-VC_2045_S_SPK13.indb 13
GB
6.2 Dry vacuuming
Use the dirt bag (14) and the additional fi lter (18)
for dry vacuuming (see point 5.2).
Always ensure that the fi lters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (15) (see
point 5.2).
Check that the fi lter is securely fi tted at all times.
When wet vacuuming, the fl oating safety switch
(5) closes when the maximum tank level is
reached. At the same time, the suction noise of
the equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Danger!
The wet/dry vac is not suitable for the vacuuming
of combustible liquids. For wet vacuuming, use
only the supplied foam fi lter.
6.4 Blowing
Connect the suction hose (10) to the blow con-
nector (9) on the wet/dry vac.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.
•
We recommend that you clean the equipment
immediately after you use it.
7.2 Cleaning the appliance head (3)
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plas-
tic parts in the appliance.
7.3 Cleaning the container (7)
The container can be cleaned with a damp cloth
and some soft soap or under running water, de-
pending on the amount of dirt.
- 13 -
03.02.2025 09:54:34
03.02.2025 09:54:34
Werbung
