Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING THE RECEIVER
2.4.5 System Information
If you have to contact your service provider or a service center
they might ask for information available from this menu.
Place the cursor on this sub menu and press the OK key.
The following will be the on-screen display.
2.4.6 Software Upgrade
You can download and upgrade the system software of the
receiver through a specific channel through a specific channel
designated by the broadcaster.
The distributor will provide you with more information about that.
If you select to download a new software version, all your previous
settings, access code and favourite channels etc. will be erased!
Downloading may take a while during downloading don't turn off
the receiver.
2.4.7 Copy Channel Data
If you want to copy the channel data from one receiver to
another, please follow the instruction below.
Please make your own channel data, such as favorite & lock
channel with your own master box.
Then take your master box when you install another box.
1. Plug on both master & slave receivers
2. Master Box(Installed Box) : Stand-by Mode
3. Slave Box(Installing Box) : Menu Mode
4. Connect 2 Boxes with RS232 serial cable
(Both end should have male connector)
5. Select the 'System Setup' and press the OK key.
6. Select the 'Copy Channel Data' with the
7. Press 'OK' to start channel data copy
GB-30
/
keys.
D
T
T
R
E
C
3.1 Playing a Disc
Ensure that your DTB-D700F is connected correctly to the TV and audio system, which are output
components. Turn on the power of the TV and audio system. Ensure that the local code of the
DTB-D700F is matched to that of the disc. If not matched, your disc will not be played.
The first time you press the DTT/DVD key to switch the DVD mode.
Play
- Press the OPEN/CLOSE (
The STANDBY indicator light goes out and the tray opens.
Place a disc gently into the tray with the disc's label facing up.
- Press the PLAY/PAUSE (
Stopping Play
- Press the STOP (
Removing Disc
- Press the OPEN/CLOSE key.
Pausing Play
- Press the PLAY/PAUSE (
Screen stops, no sound.
- To resume again, press the PLAY/PAUSE (
Step Motion Play (Except CD)
- Press the SKIP (
Each time the key is pressed, a new frame will appear.
No sound is heard during STEP mode.
- Press the PLAY/PAUSE (
(You can only perform step motion play in the forward direction.)
Slow Motion Play (Except CD)
- Press the SEARCH (
- By pressing the SEARCH (
1/8, 1/4 or 1/2 of normal speed.
No sound is heard during slow mode.
- Press the PLAY/PAUSE (
RESUME function
When you stop disc play, the player remembers where you stopped, so when you press the
PLAY/PAUSE (
the STOP (
N N o o t t e e
:
- If the player is left for screen saver time in pause mode, it will stop.
- If the player is left in the stop mode for more than 5 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left in the stop mode for more than two minute without any user interaction,
a screen saver will be activated. Press the PLAY/PAUSE (
- This icon
indicates an invalid key press.
E
I
V
E
R
/
D
V
D
P
L
A
3. BASIC FUNCTIONS (DVD)
) key.
√/»
) key or OPEN/CLOSE (
) key to close the disc tray.
) key during playback.
) key on the remote during playback.
√/»
) key once again.
√/»
œœ / √√
) key on the remote during PAUSE mode.
√/»
) key to resume normal play.
œœ / √√
) key on the remote during PAUSE mode.
œœ / √√
) key, you can select slow motion play for
√/»
) key twice to resume normal play.
√/»
) key again, it will pick up where you left off. (unless the disc is removed,
) key is pressed twice or the player is unplugged.)
√/»
GB-31
Y
E
R
) key to resume normal play.
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
