cecotec CONGA 9590 SPIN REVOLUTION ULTRA POWER HOME Bedienungsanleitung Seite 33

ENGLISH
Once in the app, press on the "+" symbol in the top right corner and the "Add device" option.
On your robot vacuum cleaner, press and hold for a few seconds the Home button until the
robot beeps and the buttons change their flashing frequency.
Press on the robot option you are using.
Enter your home Wi-Fi password.
Follow the steps shown in the app until the linking process is completed.
First use
- Once the robot vacuum cleaner and the self-emptying base are installed, follow the steps
below before the first cleaning.
- First of all, fully charge the robot vacuum cleaner. It is suggested to allow the robot to
charge overnight. Once fully charged, it may carry out the first cleaning cycle and save the
first map. To do this, press the start/pause button in the app and the robot will map your
house to continue cleaning in the edge and zigzag mode.
- If your house is very large and the robot vacuum cleaner runs out of battery, it will return
to the self-emptying base, save both complete and incomplete maps, and, once recharged,
it will resume cleaning where it left off until the entire cleaning surface has been mapped.
The robot vacuum cleaner is constantly mapping, so it adapts in an individualised and
personalised way to the particularities of each house while constantly improving its map.
About the self-emptying base
- The self-emptying base includes a loading and emptying function and a new dirt-
disposal bag. After cleaning, the robot will automatically return to the self-emptying
base to recharge. The self-emptying base will empty the dirt tank based on the emptying
scheduled selected on the app.
- If the robot vacuum cleaner is charging in the self-emptying base, you can force the robot
to self-empty. To do so, press the "Self-emptying" option in your application.
3. OPERATION
Robot vacuum cleaner's buttons
Auto Mode
- Press the Start/Pause button on the robot vacuum cleaner or from the app for the robot
to automatically start cleaning in Edge mode and perform a cleaning cycle in an orderly
zig-zag pattern, while recognising which areas it has cleaned and which it hasn't. The
robot vacuum cleaner will automatically plan the cleaning route during cleaning.
- If you control the robot vacuum cleaner manually during this mode, the robot will
recalculate the route, so it may pass through already cleaned areas. To ensure efficient
cleaning, do not operate the robot vacuum cleaner manually during automatic cleaning.
64
Conga 9590 Spin Revolution Ultra Power Home
- Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle,
the robot vacuum cleaner will smartly return to the charging base automatically and once
fully charged, it will resume the cleaning process from the same point.
- During cleaning, the robot vacuum cleaner will stop briefly to evaluate the area and
calculate the cleaning route (this stop will vary depending on the house conditions).
Back Home mode
- Press the Back Home button on the robot vacuum cleaner or from the app to send the robot
vacuum cleaner to the self-emptying base. The robot vacuum cleaner will stop vacuuming
until it reaches the base.
- This mode can be activated during any cleaning cycle.
- The robot vacuum cleaner will take the shortest route back to the self-emptying base
thanks to its map-memorisation feature and the smart Back Home function.
- Upon completing a cleaning cycle or when the battery is low, thanks to its TotalSurface 2.0
technology, the robot vacuum cleaner will automatically return to the self-emptying base
to avoid running out of battery. Once the robot has recharged, it will resume cleaning from
the point it has stopped.
Note:
The robot vacuum cleaner will not be able to return to the self-emptying base if it can't easily
access it. If this happens, manually place it in the self-emptying base.
Functions
Pause
While the robot vacuum cleaner is running, press the Start/Pause button on the robot vacuum
cleaner or select it in the app to pause the cleaning process. Press the Start/Pause button on
the robot vacuum cleaner or on the app to resume the cleaning process.
Standby
The robot vacuum cleaner will automatically enter standby mode after 10 minutes of inactivity.
Press the Start/Pause button on the robot vacuum cleaner or in the app to activate it again.
Cleaning modes
- The robot vacuum cleaner includes different modes and functions that can be toggled
from the app.
- In addition, in every one of the cleaning modes on the app, you will be able to select the
Turbo mode on carpets, which activates the maximum suction power when the robot
vacuum cleaner detects a carpet, and the x2 option which allows the selected cleaning
mode to be doubled.
ENGLISH
65
Conga 9590 Spin Revolution Ultra Power Home