Getting Started; Functional Description - Evolution Sds4-800 Originalbetriebsanleitung

®
ASSEMBLY
Your Evolution Power Tools saw is shipped complete. Remove
all contents from the box and inspect to ensure no damage was
incurred during shipping, and that the items listed below are
included.
Description
Instruction Manual
Side Handle
Depth Gauge
SDS Drills
SDS Chisels

GETTING STARTED

CAUTION! ALWAYS DISCONNECT THE DRILL FROM POWER
SOURCE BEFORE MAKING ADJUSTMENTS.
Refer to the "Service Parts List Drawing".

FUNCTIONAL DESCRIPTION

CAUTION! Always be sure that the tool is switched off and
unplugged before adjusting or checking a function on the tool.
Switch action (see FIG 1)
CAUTION!
• Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the 'OFF' position
when released.
• The switch can be locked in the 'ON' position for ease of
operator comfort during extended use. Apply caution when
locking the tool in the 'ON' position and maintain a firm grip on
the tool.
To start the tool, simply pull the switch trigger. Tool speed is
increased by increasing pressure on the switch trigger. Release
the switch trigger to stop the drill.
For continuous operation, pull the switch trigger and then push
in the lock button.
To stop the tool from the locked position, pull the switch trigger
fully, then release it.
A speed control screw is provided so that the maximum tool
speed can be limited (variable). Turn the speed control screw
clockwise for higher speed, and counterclockwise for lower
speed.
Reversing switch action (see FIG 1)
This drill has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the required
position (clockwise or counterclockwise rotation) as indicated
by the arrows on the drill body.
CAUTION!
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before the
tool stops may damage the tool.
Selecting the action mode (see FIG 2)
Quantity
This tool has a 4 position action mode selecting switch.
Push in the locking button on the switch lever and rotate the
1
switch to the desired position. Release the locking button and
1
ensure that the button has locked the switch in the required
position.
1
The 4 positions are:
1 x 6mm x 160mm
• Drill
1 x 8mm x 160mm
• Hammer Drill
1 x 10mm x 160mm
• Chisel (unlocked)
• Chisel (locked)
1 x 25mm x 250mm
1 x Point x 250mm
Installing the side handle (see FIG 3)
CAUTION! Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Always use the side grip handle to ensure operating safety.
Install the side grip handle onto the drill collar and secure in
place by tightening the handle. Note that the handle may be
swung through 360
home against the drill body before tightening.
Depth Gauge (see FIG 3)
The depth gauge is convenient for drilling holes of uniform
depth. To install, loosen the side grip handle and insert the
depth gauge into the hexagonal hole. Adjust to suit and tighten
the side grip handle to lock both the handle and depth gauge
into the desired position.
Installing or removing a drill bit or chisel (see FIG 4)
CAUTION! Always be sure that the tool is switched of and
unplugged before carrying out any work on the tool.
Carefully insert the SDS chisel or bit into the SDS chuck. Gently
pull the bit into the chuck whilst rotating the bit slowly. Pull
back on the chuck collar and continue pulling the bit gently
until positive location is felt and the bit slides fully home into
the chuck.
Only remove the bit when operations have finished and the bit
has completely cooled down.
To remove the bit, slide the chuck collar rearward and carefully
pull the bit out of the chuck
OPERATION
Standard Drilling Operation
Ensure that the action mode selecting switch is set on the
standard drill mode. See FIG 2
CAUTION!
• Using excessive force on the tool will not speed up the
drilling. Excessive pressure will only serve to damage the tip of
the bit, decrease the tool performance and shorten the service
life of the tool.
• There is tremendous force exerted on the tool / bit at the time
6
o . Ensure that the side handle is pushed fully