cecotec ForceClima 7550 Style Connected Bedienungsanleitung Seite 43

ENGLISH
4. OPERATION
The following functions can be activated from the control panel or from the remote control.
Power on/off
When the appliance is switched on, it will beep and enter Standby mode. Press the power
icon to turn the appliance on and off.
Modes
Press the mode icon to switch between cooling mode, heating mode (depending on the
model), fan mode, and dehumidification mode.
Sleep mode
When the appliance is in operation with the cooling mode activated, press the sleep
-
mode button to adjust the temperature. The temperature shall increase by 1 °C after one
hour and by a maximum of 2 °C after 2 hours.
When the appliance is in operation with the heating mode activated, press the sleep
-
mode button to adjust the temperature. The temperature shall decrease by 1 °C after one
hour and by a maximum of 2 °C after 2 hours.
Press the button again to deactivate sleep mode.
-
Increase and decrease
Use these icons to increase or decrease temperature and time.
Temperature cannot be increased or decreased in fan mode or dehumidification mode.
Fan speed
In cooling mode, press the corresponding icon to select a high or low wind-speed setting.
This option is not available under the dehumidification mode.
NOTE:
Under certain conditions (defrost), it may not operate at the selected speed.
Timer
To set the switch-on time
When the air conditioner is off, press the timer button and select the desired switch-on
-
time using the temperature and time setting buttons.
"Preset ON Time" will appear on the control panel.
-
You can select that the appliance switches on automatically within a period of 0 to 24 hours.
-
Press the timer button again to confirm the settings and activate the function.
-
To deactivate this function, press the timer button repeatedly until the indicator light
-
turns off.
FORCECLIMA 7150 STYLE, FORCECLIMA 7550 STYLE CONNECTED
FORCECLIMA 9150 STYLE, FORCECLIMA 9450 STYLE HEATING
84
FORCECLIMA 9550 STYLE HEATING CONNECTED, FORCECLIMA 12650 STYLE HEATING
FORCECLIMA 12850 STYLE HEATING CONNECTED
To set the switch-off time
When the air conditioner is on, press the timer button and select the desired switch-off
-
time using the temperature and time setting buttons.
"Preset OFF Time" will appear on the control panel.
-
You can select that the appliance switches off automatically within a period of 0 to 24
-
hours.
Press the timer button again to confirm the settings and activate the function.
-
To deactivate this function, press the timer button repeatedly until the indicator light
-
turns off.
Wi-Fi function
Scan the following QR codes to make the connection
Model 8163: Model 8166: Model 8168:
Drainage instructions
When the air conditioner stops operating because the water tank is full, turn it off and unplug
it from the power supply. The full-tank indicator light (FULL) will start flashing and the
appliance will not operate until the water inside the tank is drained.
Manual drainage. Fig. 13
Full tank warning
This portable air conditioner has a sensor in the tank that monitors the water level. When the
sensor detects that the tank is full and, thus, must be emptied, the corresponding indicator
light will light up. Remove the rubber cap from the bottom to drain all the water.
Protection features
Frost protection function:
In cooling and dehumidification modes, if the temperature of the evaporator outlet pipe is
too low, the appliance will automatically enter protection mode to prevent damage to the
evaporator. The appliance will restart when the temperature is restored to normal values.
Condensate water flood protection function
When the water level exceeds the maximum level allowed by the safety buoy, the appliance
will switch off and activate the FULL indicator light on the control panel. To restart the device, the
FORCECLIMA 7150 STYLE, FORCECLIMA 7550 STYLE CONNECTED
FORCECLIMA 9150 STYLE, FORCECLIMA 9450 STYLE HEATING
FORCECLIMA 9550 STYLE HEATING CONNECTED, FORCECLIMA 12650 STYLE HEATING
ENGLISH
FORCECLIMA 12850 STYLE HEATING CONNECTED
85