Adjusting The Feet; Electrical Connection - Beko WMY 91446HLB1 Bedienungsanleitung

• To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do not
immerse the hose end into the dirty water or do not
drive it in the drain more than 15 cm. If it is too long,
cut it short.
• The end of the hose should not be bent, it should
not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by
adding an original extension hose. Length of the
hose may not be longer than 3.2 m. To avoid water
leak failures, the connection between the extension
hose and the drain hose of the product must be
fitted well with an appropriate clamp as not to come
off and leak.

2.6 Adjusting the feet

A
WArNINg:
In order to ensure that the product
operates more silently and vibration-free, it must
stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise,
the product may move from its place and cause
crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and
balanced.
3. Tighten all lock nuts again by hand.
A
WArNINg:
Do not use any tools to loosen the
lock nuts. Otherwise, they will get damaged.

2.7 Electrical connection

Connect the product to a grounded outlet protected
by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is
used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the
house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
31 / EN
• The voltage specified in the "Technical
specifications" section must be equal to your mains
voltage.
• Do not make connections via extension cables or
multi-plugs.
B
WArNINg:
Damaged power cables must be
replaced by the Authorized Service Agents.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse
order of removal procedure;
C
Never move the product without the
transportation safety bolts properly fixed in place!
A
WArNINg:
Packaging materials are dangerous
to children. Keep packaging materials in a safe
place away from reach of the children.
3 Preparation
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and
degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment
tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or
wash the clothes by putting them in a laundry bag or
pillow case.
• Take out all substances in the pockets such as coins,
pens and paper clips, and turn pockets inside out
and brush. Such objects may damage the product or
cause noise problem.
• Put small size clothes such as infant's socks and
nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them.
Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips
and tears.
• Wash "machine washable" or "hand washable"
labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before
washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale
removers suitable for machine wash. Always follow
the instructions on the package.
• Wash trousers and delicate laundry turned inside
out.
• Keep laundry items made of Angora wool in the
freezer for a few hours before washing. This will
reduce pilling.
Washing Machine / User's Manual