Cleaning & Maintenance - Arktic 271551 Bedienungsanleitung

GB
• Check the water level regularly. When the water level is too low
the appliance will stop automatically and the "Water level is too
low" indicator will light up. Press the "Power ON/OFF button",
fill the water reservoir up to the level indicator and press the
"Power ON/OFF button" again.
• L et the appliance rest for 5 minutes to let the coolant in the
compressor settle before restarting the appliance.
• The ice maker stops automatically when the basket is full.
• Put fresh water in the reservoir every day.
• When not in use, empty the reservoir via the drain tap.
• Beware: Never tip the appliance more than 45° and do not turn
the appliance upside down. This will damage the appliance
beyond repair.
NOTE: The control functions are the same between 271551 and
271568 except design of control panel.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the
power supply and cool down before storage, cleaning &
maintenance.
• Do not use water jet or steam cleaner for cleaning and do
not push the appliance under the water as the parts will
get wet and electric shock might be resulted.
• I f the appliance is not kept in a good state of cleanliness,
this can adversely affect the life of the appliance and result
in a dangerous situation.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge slightly
dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned before
and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent and
rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
• Clean the condenser for every 2 ~ 3 months.
Maintenance
• C heck the operation of the appliance regularly to prevent
serious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact
the supplier.
• All maintenance, installation and repair work must be
carried out by specialised and authorised technicians, or
recommended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation.
Disconnect the appliance from power supply when moving
and hold it at the bottom.
Descaling
This appliance should be cleaned and descaled frequently.
To keep this appliance in optimum condition and to ensure
its operation, it is crucial that you descale the appliance on
a regular basis. Depending on the hardness of the water and
the frequency of use, you need to repeat the following
procedure regularly. To descale use a descaling agent that is
suitable for the appliance. You can also use pure lemon juice,
citric acid or cleaning vinegar as a de-scaling agent. To
ensure the proper mixture, read the instructions supplied
with the agent. For pure lemon juice or cleaning vinegar the
general mixture applies of 1/3 cleaning vinegar or lemon
juice to 2/3 water.
1. Fill the water reservoir with the de-scaling agent according
to the terms of the agent. Never exceed the maximum
level.
2. Turn the power switch "On". The ice cube basin will now
be filled with water. You can hear that the pump is
pumping the water from the reservoir to the ice bucket.
3. At the time the ice cube basin is filled and the water supply
stops: immediately push the button "Off".
4. The ice cube basin will reset to zero and the descaling
agent will be spread through the appliance.
5. Switch the power switch back "On".
6. Repeat this procedure (step 1 till 4) several times with de-
scaling agent.
7. After you have made sure that the appliance is totally
clean, let the descaling agent pour out of the appliance
through the drain plug on the left side of the appliance.
8. Now pour clean water in the water reservoir and repeat
step 1 till 4 several times to make sure that there are no
scraps of the descaling agent left in the appliance. The
smell and taste of the descaling agent should fully be
disappeared. Take every time new clean water for this.
9. The appliance is now ready for use again.
NOTE! Warranty is void if failure to decale regularly leads
to reduced functioning or failure of the appliance.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve
the problem, please contact the supplier/service provider.
9